1. Introduction
Thank you for choosing the SENSEA Bora 3-Jet Hand Shower Kit. This manual provides essential information for the safe installation, operation, and maintenance of your new hand shower. Please read these instructions carefully before use and retain them for future reference.
Image 1.1: SENSEA Bora 3-Jet Hand Shower Kit components.
2. Safety Information
- Ensure all connections are watertight to prevent leaks.
- Do not use abrasive cleaners or harsh chemicals on the product, as this may damage the finish.
- Always turn off the main water supply before attempting any installation or maintenance.
- If you are unsure about any installation steps, consult a qualified plumber.
3. Package Contents
The SENSEA Bora 3-Jet Hand Shower Kit includes the following components:
- 1x 3-Jet Hand Shower Head
- 1x Universal Anti-Twist Flexible Hose (175 cm)
- 1x Adjustable Wall Mount Bracket
- Installation hardware (screws, wall plugs)
- Rubber gaskets
Image 3.1: All components included in the SENSEA Bora kit. Note the anti-twist hose and water-saving feature.
4. Setup and Installation
Follow these steps to install your SENSEA Bora Hand Shower Kit:
- Prepare the Installation Area: Choose a suitable location on your bathroom wall for the mount bracket. Ensure the surface is clean and dry.
- Mark Drilling Points: Hold the wall mount bracket against the wall at the desired height and mark the drilling points with a pencil.
- Drill Holes: Use an appropriate drill bit to drill holes at the marked points. Insert the provided wall plugs into the drilled holes.
- Attach Wall Mount: Secure the wall mount bracket to the wall using the provided screws.
- Connect Flexible Hose: Attach one end of the flexible hose to your shower mixer outlet and the other end to the hand shower head. Ensure rubber gaskets are properly seated at both connections to prevent leaks. Hand-tighten only, then use a wrench for a final quarter turn if necessary, being careful not to overtighten.
- Place Hand Shower: Insert the hand shower head into the wall mount bracket.
Image 4.1: Diagram showing the dimensions of the hand shower (10 cm diameter, 175 cm hose length) and the installation hardware for the wall mount.
5. Operating Instructions
The SENSEA Bora hand shower features three distinct jet modes for a customized showering experience. It also includes a water-saving regulator.
5.1. Changing Jet Modes
To switch between the three jet modes, simply press the 'JETS' button located on the hand shower head. Each press will cycle through the available modes:
- Mode 1: Rain - A gentle, wide spray for a relaxing shower.
- Mode 2: Tonic - A more focused, invigorating spray.
- Mode 3: Massage - A powerful, pulsating spray for muscle relaxation.
Image 5.1: Press the 'JETS' button to easily change between spray modes.
Image 5.2: Visual representation of the three distinct jet patterns: Rain, Tonic, and Massage.
5.2. Water Saving Feature
The Bora hand shower is equipped with an integrated flow regulator that can help reduce water consumption by up to 25% compared to traditional shower heads. This feature is automatic and requires no user intervention.
6. Maintenance
Regular cleaning will ensure the longevity and optimal performance of your hand shower.
6.1. Anti-Limescale Nozzles
The silicone nozzles are designed to limit limescale buildup. If limescale deposits do form, they can be easily removed by gently rubbing the flexible nozzles with your finger or a soft cloth. This helps maintain consistent water flow and spray patterns.
Image 6.1: Demonstrating how to easily clean the anti-limescale silicone nozzles.
6.2. General Cleaning
Clean the hand shower head, hose, and wall mount regularly with a soft cloth and mild soap. Rinse thoroughly with water and dry with a soft cloth. Avoid using abrasive sponges, scouring agents, or chemical cleaners, as these can damage the matte finish.
7. Troubleshooting
If you encounter any issues with your SENSEA Bora hand shower, please refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| Low water pressure | Clogged nozzles or filter | Clean the silicone nozzles (see Section 6.1). Check and clean the filter washer at the hose connection. |
| Leaks at connections | Loose connections or worn gaskets | Ensure connections are hand-tightened. Check if rubber gaskets are properly seated and replace if worn. |
| Difficulty changing jet modes | Mineral buildup in the mechanism | Run hot water through the shower head for a few minutes. If the issue persists, soak the shower head in a descaling solution (e.g., vinegar and water) for a short period, then rinse thoroughly. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | SENSEA |
| Model Number | 3276000698326 |
| Color | Matte Black |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Hand Shower Dimensions (L x W) | Approx. 175 mm x 100 mm (head diameter) |
| Hose Length | 175 cm |
| Weight | 590 g |
| Number of Jet Modes | 3 (Rain, Tonic, Massage) |
| Special Features | Anti-limescale nozzles, Water-saving regulator, Anti-twist flexible hose |
| Installation Type | Wall Mount |
9. Warranty and Support
For warranty information and customer support, please refer to the documentation provided at the point of purchase or visit the official SENSEA website. Keep your proof of purchase for any warranty claims.
