QINIZX InduBalce-5S

Download PDF
Contents

QINIZX 5S Active Battery Equalizer Balancer Instruction Manual

Model: InduBalce-5S

1. Introduction

The QINIZX 5S Active Battery Equalizer Balancer is an inductive energy transfer board designed to actively balance the voltage of individual cells within a 5-series (5S) lithium-ion (Li-ion), lithium polymer (Lipo), or lithium iron phosphate (LiFePO4/LFP) battery pack. This device helps maintain cell voltage consistency, which is crucial for the longevity and performance of your battery pack. It operates by transferring energy between adjacent cells to equalize their voltage differences.

This equalizer is an auxiliary component and is not a Battery Management System (BMS). It does not provide overvoltage or overdischarge protection. For comprehensive battery protection, it is recommended to use this equalizer in parallel with a suitable BMS protection board.

2. Safety Information and Warnings

Read all instructions carefully before installation and use. Failure to follow these safety guidelines may result in damage to the product, battery pack, or personal injury.

  • This product is designed for 5S battery packs only. Do not use with other cell counts.
  • Ensure all battery cells are wired correctly before connecting the equalization board. Incorrect wiring can cause short-circuits and damage the board.
  • Always ensure proper insulation for all connections to prevent accidental short-circuits.
  • When inserting the cable plug, do so obliquely, ensuring the "B-" pin makes contact first. Improper insertion may cause the board to burn out.
  • This equalization board is not a BMS. It does not provide overvoltage, undervoltage, or overcurrent protection. It must be used in conjunction with a BMS for full battery protection.
  • Do not use with low-quality or severely imbalanced battery packs, as this may cause the indicator light to flash and report errors.
  • The board may become warm during active balancing, especially with significant cell imbalances. This is normal operation.

3. Product Overview

The QINIZX 5S Active Battery Equalizer Balancer features an inductive energy transfer mechanism to achieve cell voltage balance. It is compact and designed for integration into various battery applications.

Top view of the QINIZX 5S Active Battery Equalizer Balancer board, showing components and connection points.

Figure 3.1: Top view of the QINIZX 5S Active Battery Equalizer Balancer board, displaying the inductive coils, integrated circuits, and the 6-pin connector for battery cell connections.

Bottom view of the QINIZX 5S Active Battery Equalizer Balancer board.

Figure 3.2: Bottom view of the QINIZX 5S Active Battery Equalizer Balancer board, showing the PCB traces and mounting holes.

Key Features:

  • Active Balancing: Utilizes inductive energy transfer for efficient cell balancing.
  • Compatibility: Supports NCM (Li-ion), Lipo, and LFP (LiFePO4) battery types. Not compatible with LTO batteries.
  • Voltage Range: Single cell voltage working range of 3.0V to 4.2V.
  • Balance Current: Up to 1.2A maximum balance current, depending on voltage difference.
  • Balance Accuracy: Achieves a typical adjacent voltage balance accuracy of 30mV.
  • Indicator Lights: LED indicators for balance status and error detection.
  • Compact Size: PCB dimensions approximately 2.08 x 2.04 x 0.31 inches.

4. Specifications

FeatureSpecification
Applicable Battery TypeNCM (Li-ion), Lipo, LFP (LiFePO4)
Incompatible Battery TypeLTO
Number of Series Cells5S (5 series)
Single Cell Voltage Range3.0V - 4.2V
Suggested Battery CapacityBelow 30AH
Balance MethodInductive Energy Transfer
Balance Trigger Voltage Difference> 0.1V (adjacent cells)
Balance Stop Voltage Difference< 0.03V (adjacent cells)
Balance Current (0.1V-0.2V diff)0.5A - 0.7A
Balance Current (>0.2V diff)1.0A (max 1.2A)
Voltage Balance Accuracy30mV (typical, between adjacent voltages)
Under-voltage Protection Dormant Voltage< 0.03V (adjacent cells)
Sleep Current10µA
PCB Dimensions (L x W x H)2.08 x 2.04 x 0.31 inches (53 x 52 x 8 mm)
Accessories Included1x Active Balance PCB, 1x 6-pin XH2.54mm terminal wire (1.3ft / 22AWG)
Diagram showing the dimensions of the QINIZX 5S Active Battery Equalizer Balancer board in inches.

Figure 4.1: Dimensional drawing of the equalizer board, indicating its compact size for integration.

5. Setup and Installation

Careful wiring is essential for the correct and safe operation of the equalizer board. Always ensure the battery pack is partially discharged before beginning installation.

Wiring Definition (for 5S battery pack):

  • B-: The total negative pole of the battery pack (negative pole of the first battery).
  • B1: The positive pole of the first battery.
  • B2: The positive pole of the second battery.
  • B3: The positive pole of the third battery.
  • B4: The positive pole of the fourth battery.
  • B5: The positive pole of the fifth battery (and the total positive pole of the 5S pack).
Wiring diagram for the 5S active equalizer balancer, showing connections from B- to B5+ on a battery pack.

Figure 5.1: Wiring diagram illustrating the correct connection points for the 6-pin cable to a 5S battery pack.

Installation Steps:

  1. Prepare Battery Pack: Ensure your 5S battery pack is partially discharged.
  2. Wire Connections: Solder or securely connect each wire from the provided 6-pin XH2.54mm terminal cable to the corresponding battery cell terminals as defined above (B-, B1, B2, B3, B4, B5). Double-check all connections for correctness and polarity.
  3. Insulation: After wiring, ensure all exposed connections are properly insulated to prevent short-circuits.
  4. Connect to Board: Carefully insert the wired 6-pin connector into the socket on the equalizer board. Remember to insert it obliquely, ensuring the "B-" pin makes contact first.
  5. Initial Check: After connection, observe the LED indicators on the board. Refer to the "Operation" section for indicator light meanings.
The QINIZX 5S active equalizer balancer connected to a 5S battery pack with wires, viewed from the side.

Figure 5.2: Example of the equalizer board connected to a 5S battery pack, showing the wiring harness extending to the cells.

The QINIZX 5S active equalizer balancer connected to a 5S battery pack with wires, viewed from above.

Figure 5.3: Top-down view of the equalizer board connected to a 5S battery pack, illustrating the overall setup.

6. Operation

The QINIZX 5S Active Battery Equalizer Balancer operates automatically to maintain cell voltage balance. It continuously monitors the voltage differences between adjacent cells.

Balancing Mechanism:

  • The equalization process is triggered when the voltage difference between any two adjacent cells exceeds 0.1V.
  • Energy is transferred from the higher voltage cell to the lower voltage cell until the voltage difference between them is less than 0.03V, at which point balancing for that pair stops.
  • For optimal balancing, especially with new or significantly imbalanced packs, it may be necessary to charge and discharge the battery pack multiple times.

Indicator Light Status:

  • LED On: Indicates that active balancing is currently in progress for the corresponding cell pair.
  • LED Off: Indicates that balancing for the corresponding cell pair has ended, or the voltage difference is below the trigger threshold.
  • LED Flashing: Indicates a potential issue such as a battery drop string (disconnected cell) or a circuit failure. Refer to the Troubleshooting section.

7. Troubleshooting

ProblemIndicatorPossible CauseSolution
Board not balancing / No LEDs onAll LEDs Off
  • All cells are already balanced (voltage difference < 0.03V).
  • Incorrect wiring or poor connection.
  • Battery pack is not 5S.
  • Verify cell voltages with a multimeter.
  • Check all wiring connections for correctness and secure contact.
  • Ensure the battery pack is a 5S configuration.
Board not balancing / Some LEDs onSome LEDs On, some Off
  • Only specific cell pairs require balancing.
  • This is normal operation. The board is balancing the detected imbalanced cell pairs.
Error indicationLED Flashing
  • Battery drop string (disconnected cell).
  • Circuit failure on the board.
  • Severely imbalanced or poor-quality battery cells.
  • Immediately disconnect the board.
  • Check all wiring connections for continuity and secure contact.
  • Verify individual cell voltages. If a cell is significantly lower or higher than others, it may be faulty.
  • If wiring and cells are confirmed good, the board may be faulty.
Board gets excessively hotN/A
  • Significant voltage imbalance between cells, causing high balancing current.
  • This can be normal during initial balancing of a highly imbalanced pack. Ensure adequate ventilation.
  • If heat persists after initial balancing, check for short-circuits or faulty cells.

8. Maintenance

The QINIZX 5S Active Battery Equalizer Balancer is designed for maintenance-free operation. Ensure the board and its connections remain clean, dry, and free from physical damage. Periodically inspect wiring for wear or loose connections, especially in applications subject to vibration.

9. Warranty and Support

Specific warranty information for this product is not provided in this manual. For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly through your purchase platform.

Note: Damage resulting from incorrect wiring, improper installation, or failure to adhere to safety warnings may void any applicable warranty.

QINIZX 5S Active Battery Equalizer Balancer Manual

© 2026 QINIZX. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.