Ingco CKLI1201 12V Cordless Drill and Impact Driver Set User Manual

1. Introduction

Thank you for choosing the Ingco CKLI1201 12V Cordless Drill and Impact Driver Set. This manual provides essential information for the safe operation, maintenance, and troubleshooting of your new power tools. Please read this manual thoroughly before using the tools and keep it for future reference.

This set includes a versatile cordless drill and a powerful impact driver, both powered by 12V Lithium-ion batteries, designed for various drilling and fastening tasks.

2. Safety Instructions

General Power Tool Safety Warnings:

• Work Area Safety: Keep your work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
• Electrical Safety: Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Personal Safety: Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Power Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or remove the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Battery Tool Use and Care: Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

3. Package Contents

Your Ingco CKLI1201 set includes the following items:

• 1 x 12V Cordless Drill
• 1 x 12V Impact Driver
• 2 x 1.5Ah Lithium-ion Batteries
• 1 x Battery Charger (220V-240V~50/60Hz)
• 1 x Canvas Carry Bag
• Assorted Drill Bits and Driver Bits (as pictured)

Image 1: Ingco CKLI1201 Drill and Impact Driver Set with accessories. This image displays the cordless drill, impact driver, two batteries, a charger, a canvas carry bag, and various drill and driver bits included in the package.

4. Setup

4.1. Charging the Battery

1. Ensure the charger is connected to a standard 220V-240V~50/60Hz power outlet.
2. Slide the 1.5Ah Lithium-ion battery into the charger until it clicks into place.
3. Observe the indicator light on the charger. It will typically show red during charging and turn green when fully charged.
4. Once fully charged, remove the battery from the charger. Do not overcharge the battery.

Note: New batteries are not fully charged and should be charged before first use. Refer to the charger's specific instructions for detailed charging times and indicator light meanings.

4.2. Installing/Removing Battery Pack

1. To install: Align the battery pack with the base of the tool handle. Slide the battery pack into the tool until it locks securely in place.
2. To remove: Press the battery release button (usually located on the side or front of the battery pack) and slide the battery pack out of the tool.

4.3. Installing Drill Bits (Cordless Drill)

1. Ensure the drill is switched off and the battery is removed for safety.
2. Grip the rear half of the chuck and rotate the front half counter-clockwise until the chuck jaws are open wide enough to accept the drill bit.
3. Insert the drill bit into the chuck as far as it will go.
4. Grip the rear half of the chuck and rotate the front half clockwise to tighten the chuck jaws securely around the drill bit. Ensure the bit is centered.
5. Chuck Capacity: 0.8-10mm.

4.4. Installing Driver Bits (Impact Driver)

1. Ensure the impact driver is switched off and the battery is removed for safety.
2. Pull the quick-release collar forward.
3. Insert the driver bit into the hex chuck.
4. Release the quick-release collar. The bit should be securely held. Pull on the bit to ensure it is locked.

5. Operating Instructions

5.1. Cordless Drill Operation

• Speed Settings: The drill features a 2-speed mechanical gearbox. Use the speed selector switch (usually on top of the drill) to choose between low speed (0-350/min) for high torque applications (e.g., driving screws, large diameter drilling) and high speed (0-1350/min) for faster drilling.
• Torque Settings: The torque adjustment collar (15+1 settings) allows you to select the desired torque. Lower settings are for driving small screws or working with soft materials to prevent over-tightening or stripping. Higher settings are for larger screws or harder materials. The drill setting (represented by a drill bit icon) bypasses the clutch for maximum torque when drilling.
• Forward/Reverse Switch: Located above the trigger, this switch controls the direction of rotation. Push left for forward (drilling/tightening), push right for reverse (removing screws/loosening). Center position locks the trigger for safety.
• Trigger Switch: Press the trigger to start the drill. The speed is variable depending on how far you press the trigger.
• LED Light: An integrated LED light illuminates the work area when the trigger is pressed.

5.2. Impact Driver Operation

• Forward/Reverse Switch: Similar to the drill, this switch controls the rotation direction.
• Trigger Switch: Press the trigger to start the impact driver. The speed is variable (0-2000 RPM) and the impact rate (0-2600 IPM) depends on trigger pressure.
• Impact Mechanism: The impact driver applies rotational force and rapid, short hammer blows (impacts) to drive fasteners. This is particularly effective for driving long screws or fasteners into dense materials.
• LED Work Light: An integrated LED work light illuminates the fastening area.

6. Maintenance

• Cleaning: Keep the ventilation openings of the tools clean to prevent overheating. Use a soft, damp cloth to clean the tool housing. Do not use harsh chemicals or abrasive cleaners.
• Battery Care: Store batteries in a cool, dry place away from direct sunlight and extreme temperatures. Do not store fully discharged batteries for extended periods. Charge them periodically if not in use.
• Storage: When not in use, store the tools, batteries, and charger in the provided canvas bag in a dry, secure location out of reach of children.
• Inspection: Regularly inspect the tools for any signs of damage, loose screws, or worn parts. If any damage is found, do not use the tool and have it repaired by a qualified service technician.

7. Troubleshooting

If you encounter problems not listed here or if solutions do not resolve the issue, please contact customer support.

8. Specifications

• Model: CKLI1201
• Voltage: 12V
• Battery Type: Lithium-ion
• Battery Capacity: 1.5Ah
• Charger Voltage: 220V-240V~50/60Hz
• Material: Metal (housing components)
• Product Dimensions: 8 x 36 x 21.5 cm
• Weight: 2.76 kg (total item weight)

Cordless Drill Specifications:

• No-load Speed: 0-350/0-1350/min
• Max Torque: 20NM
• Chuck Capacity: 0.8-10mm
• Torque Settings: 15+1
• Gearbox: 2-speed mechanical
• Features: Integrated LED light

Impact Driver Specifications:

• No-load Speed: 0-2000 RPM
• Rated Impact Rate: 0-2600 IPM
• Max Torque: 100 NM
• Features: Integrated LED work light

9. Warranty and Support

Specific warranty information for the Ingco CKLI1201 set is not provided in this manual. For details regarding warranty coverage, service, or technical support, please refer to the warranty card included with your product or contact your local Ingco dealer or customer service representative.

You may also visit the official Ingco website for further assistance and contact information.