Aurabeat AG+ Go Silver Ion Antiviral Air Purifier

1. Introduction

Thank you for choosing the Aurabeat AG+ Go Silver Ion Antiviral Air Purifier. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your new air purifier. Please read this manual thoroughly before using the product and retain it for future reference.

The Aurabeat AG+ Go Air Purifier, a compact and modern device designed for air purification.

2. Important Safety Instructions

To reduce the risk of fire, electric shock, or injury, please observe the following safety precautions:

• Always unplug the air purifier before moving it, opening the grille, changing filters, or whenever it is not in use.
• Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
• Use the air purifier only for its intended household use as described in this manual.
• Do not use outdoors.
• Do not allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or damage the air purifier.
• Do not block air openings or operate near soft surfaces like a bed or sofa, where openings may become blocked.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

3. Product Components

Familiarize yourself with the parts of your Aurabeat AG+ Go Air Purifier:

• Main Unit
• AG+ High Efficiency Antiviral Air Filter (Pre-installed or separate)
• Power Cord
• Remote Control

Top panel of the Aurabeat AG+ Go Air Purifier, showing the control buttons for power, timer, fan speed, and mode selection.

4. Setup

4.1 Unpacking

1. Carefully remove the air purifier from its packaging.
2. Remove all packaging materials, including any protective film or tape.
3. Check for any damage during transit. If damaged, do not operate and contact customer support.

4.2 Filter Installation

The AG+ High Efficiency Antiviral Air Filter may come pre-installed or require installation. If not pre-installed, follow these steps:

1. Ensure the unit is unplugged from the power outlet.
2. Locate the filter compartment cover, typically on the side or back of the unit.
3. Open the cover according to the markings or instructions on the unit.
4. Remove the new filter from its protective plastic packaging.
5. Insert the filter into the compartment, ensuring it is oriented correctly (refer to arrows on the filter or compartment).
6. Close the filter compartment cover securely.

The Aurabeat AG+ Go Air Purifier with its side panel removed, revealing the multi-layer filter assembly ready for installation or replacement.

4.3 Placement

• Place the air purifier on a firm, level surface.
• Ensure there is at least 15-20 cm (6-8 inches) of clear space around all sides of the unit for optimal airflow.
• Avoid placing the unit near heat sources, direct sunlight, or in areas with high humidity.

4.4 Power Connection

Plug the power cord into a standard electrical outlet. The unit is now ready for operation.

5. Operating Instructions

5.1 Power On/Off

• Press the Power Button () on the top control panel or remote control to turn the unit ON or OFF.

5.2 Fan Speed Adjustment

• Press the Fan Speed Button () repeatedly to cycle through different fan speed settings (e.g., Low, Medium, High, Auto). Indicators on the panel will light up to show the current speed.

5.3 Timer Function

• Press the Timer Button () to set the operating time (e.g., 6 hours, 9 hours, 12 hours). The unit will automatically turn off after the set time.

5.4 Ionizer Function

• The air purifier features an ionizer. Refer to the control panel or remote for a dedicated ionizer button or a mode that includes ionization. This function helps to further purify the air by releasing negative ions.

5.5 Night Light

• The unit includes a night light feature. Press the designated button (if available) to turn the night light ON or OFF.

6. Maintenance

6.1 Filter Replacement

The AG+ High Efficiency Antiviral Air Filter has a limited lifespan and needs regular replacement to maintain optimal performance. The filter life depends on usage and air quality. A filter replacement indicator light may illuminate when it's time to replace the filter.

1. Ensure the air purifier is unplugged.
2. Open the filter compartment cover.
3. Carefully remove the old filter. Dispose of the used filter responsibly.
4. Insert a new Aurabeat AG+ Go replacement filter (model specific).
5. Close the filter compartment cover securely.
6. Plug in the unit. If there is a filter reset button, press and hold it for a few seconds to reset the filter life indicator.

6.2 Cleaning the Exterior

• Always unplug the unit before cleaning.
• Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Do not allow water to drip into the interior of the air purifier.

7. Troubleshooting

If you encounter issues with your air purifier, refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact customer support.

8. Specifications

9. Warranty and Support

This Aurabeat AG+ Go Air Purifier is covered by a limited warranty. Please refer to the warranty card included with your product for specific terms and conditions. Keep your purchase receipt as proof of purchase.

For technical support, replacement parts, or warranty claims, please contact Aurabeat customer service through their official website or the contact information provided in your product packaging.