Product Overview
The 509 Aviator 2.0 Ignite S1 Goggle features the 5MAG magnetic lens system and Ignite S1 technology. This system provides a wire-free, auto-heating lens designed to eliminate fog, enhanced by a low-profile integrated fan that removes moist air from the frame. This goggle is engineered for optimal optical clarity and performance in snowmobiling conditions.
Front view of the 509 Aviator 2.0 Ignite S1 Snow Goggle, showcasing the mirrored lens and frame design.
Safety Information
- Always ensure the goggle is properly fitted and secured before use.
- Do not attempt to modify the goggle or its components, as this may compromise safety and void the warranty.
- Keep the battery pack and charging cable away from water and extreme temperatures.
- This item complies with US Federal Motor Vehicle Safety Standard 218 (FMVSS 218) (DOT FMVSS No. 218 Certified).
Setup
1. Initial Charging
Before first use, fully charge the Ignite battery pack. Connect the charging cable to the battery pack and a suitable USB power source. The indicator light on the battery pack will show charging status.
The Ignite battery pack connected to the goggle and charging. A blue indicator light is visible.
2. Attaching the Battery Pack
The battery pack securely attaches to the goggle strap. Ensure the cable is properly connected to the goggle for the Ignite system to function.
3. Adjusting the Strap
Adjust the elastic strap for a snug, comfortable fit around your head or helmet. The strap features silicone grips to prevent slipping.
4. Lens Installation/Removal
The 5MAG magnetic lens system allows for quick and easy lens changes. To remove, gently pull the lens away from the frame. To install, align the lens with the magnetic points on the frame and allow it to snap into place.
Video demonstrating the magnetic lens system for easy lens installation and removal on the 509 Aviator 2.0 Ignite S1 Goggle.
Operating Instructions
1. Powering On/Off the Ignite System
Press and hold the power button on the battery pack for 3 seconds to turn the Ignite system on or off. An indicator light will confirm the status.
2. Ignite System Modes
- Auto Mode: The system automatically detects fogging and activates the heating element and fan as needed. This is the default mode upon powering on.
- Manual Mode: Press the power button briefly to cycle through heating and fan settings manually. This allows for continuous operation or specific adjustments based on conditions.
3. Fan Operation
The integrated fan works in conjunction with the heated lens to circulate air and remove moisture, further preventing fogging. The fan speed may vary depending on the selected mode or environmental conditions.
Maintenance
1. Cleaning the Lens
- Use only a soft, non-abrasive cloth (e.g., microfiber) to clean the outer lens surface.
- For stubborn dirt, lightly dampen the cloth with water. Do not use harsh chemicals or abrasive cleaners.
- Avoid wiping the inner lens surface, as it has an anti-fog coating that can be damaged. If necessary, gently dab with a soft cloth.
2. Cleaning the Frame and Foam
Wipe the goggle frame with a damp cloth. The foam can be gently cleaned with mild soap and water, then allowed to air dry completely before storage.
3. Battery Care and Storage
- Store the goggle and battery pack in a cool, dry place.
- For long-term storage, ensure the battery is charged to approximately 50% to prolong its lifespan.
- Avoid exposing the battery to extreme heat or cold.
Troubleshooting
- Goggle is fogging:
- Ensure the Ignite system is powered on and operating in Auto or Manual mode.
- Check battery charge level. A low battery may reduce heating and fan performance.
- Verify that the goggle foam is properly sealed against your face to prevent air gaps.
- Battery not charging or short battery life:
- Confirm the charging cable is securely connected to both the battery pack and the power source.
- Try a different USB power adapter or cable to rule out a faulty accessory.
- Ensure the battery pack is not exposed to extreme cold, which can temporarily reduce battery performance.
- Fan not working:
- Check if the Ignite system is powered on.
- Ensure the battery is adequately charged.
- Inspect the fan area for any obstructions.
Specifications
| Feature | Detail |
|---|---|
| Model Name | Aviator 2.0 Ignite S1 Snow Goggle |
| Item Model Number | F02010300 |
| Brand | 509 |
| Lens Material | Polycarbonate |
| Frame Material | Polycarbonate (PC) |
| Special Features | Heated Lens (Ignite S1), Integrated Fan, Adjustable Strap |
| Lens Coating | Anti-Fog Coating |
| UV Protection | Yes |
| Sport Type | Snowmobiling |
| Fit Type | Universal |
| Item Dimensions | 9.5 x 4.5 x 4.5 inches |
| UPC | 843614156301 |
Warranty Information
The 509 Aviator 2.0 Ignite S1 Snow Goggle comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects in materials and workmanship. It does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear. For warranty claims, please retain your proof of purchase and contact 509 customer support.
Customer Support
For further assistance, technical support, or to inquire about replacement parts, please visit the official 509 website or contact their customer service department. You can find contact information and additional resources on their website: Visit the 509 Store on Amazon.
