Instruction Manual

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Shad Side Bag Holder, model H0CR61SE, designed specifically for the Honda CB650R motorcycle. This product is engineered to provide a secure and stable mounting solution for Shad semi-rigid side bags, enhancing your motorcycle's luggage capacity.

2. Safety Information

Always prioritize safety when installing and using motorcycle accessories. Failure to follow these instructions may result in injury or damage to your motorcycle or the product.

• Ensure the motorcycle is stable and on a level surface before beginning installation.
• Turn off the engine and allow exhaust components to cool down before handling.
• Wear appropriate personal protective equipment, such as gloves and eye protection.
• Do not exceed the maximum weight capacity specified for your side bags or motorcycle.
• Regularly check all mounting bolts and fasteners for tightness, especially after the first few rides.
• If you are unsure about any step of the installation, consult a qualified motorcycle mechanic.

3. Setup and Installation

The Shad Side Bag Holder (H0CR61SE) is designed for a specific fit on the Honda CB650R. Installation typically involves mounting the support frames to existing points on the motorcycle frame. Some disassembly of motorcycle fairings may be required.

Image: Components of the Shad Side Bag Holder before assembly. This image shows the various metal brackets and fasteners included in the kit, laid out on a flat surface, ready for installation.

Required Tools:

• Metric Allen key set
• Metric wrench set
• Torque wrench (recommended)
• Plastic trim removal tool (if fairing removal is needed)

Installation Steps:

1. Prepare the Motorcycle: Park the motorcycle on its center stand or a paddock stand on a firm, level surface. Ensure the engine is off and cool.
2. Remove Necessary Components: Carefully remove any fairings, seat, or other components that obstruct access to the frame mounting points as indicated in the detailed instructions provided with the product packaging.
3. Attach Mounting Brackets: Identify the specific mounting points on the motorcycle frame. Attach the primary mounting brackets using the provided hardware. Do not fully tighten bolts at this stage.
4. Assemble Side Frames: Connect the side bag support frames to the primary mounting brackets. Ensure proper alignment and fitment.
5. Secure All Fasteners: Once all components are in place and aligned, progressively tighten all bolts and nuts to the torque specifications provided in the product's detailed installation guide.
6. Reinstall Components: Reattach any fairings, seat, or other components that were removed. Ensure all clips and fasteners are securely in place.

Image: A red Honda CB650R motorcycle with the Shad Side Bag Holder installed on the left side, ready to accept a semi-rigid side bag. The holder integrates cleanly with the motorcycle's design.

4. Operating Instructions

Once the side bag holder is securely installed, it provides a stable platform for attaching compatible Shad semi-rigid side bags.

Attaching Side Bags:

1. Align the mounting points on your Shad semi-rigid side bag with the corresponding attachment points on the side bag holder.
2. Secure the bag using the integrated locking mechanism or straps provided with your Shad side bags. Ensure an audible click or firm tension indicates a secure attachment.
3. Verify that the bag is firmly attached and does not wobble or interfere with any motorcycle components (e.g., exhaust, chain, wheel).

Detaching Side Bags:

1. Unlock or release the securing mechanism on the side bag.
2. Carefully lift the bag away from the holder.

Image: A red Honda CB650R motorcycle equipped with both a Shad semi-rigid side bag on the left and a Shad top case mounted on the rear rack, demonstrating the full luggage system capability.

5. Maintenance

Regular maintenance ensures the longevity and safe operation of your side bag holder.

• Cleaning: Clean the holder regularly with mild soap and water. Avoid abrasive cleaners or solvents that could damage the finish.
• Inspection: Periodically inspect all mounting points, bolts, and the frame for any signs of wear, corrosion, or damage. Ensure all fasteners remain tight.
• Lubrication: If any moving parts or quick-release mechanisms are present, lubricate them sparingly with a suitable lubricant as needed.

6. Troubleshooting

If you encounter issues with your side bag holder, consider the following common solutions:

• Loose Fitment: If the holder feels loose, re-check all mounting bolts and ensure they are tightened to the manufacturer's specifications. Over time, vibrations can cause fasteners to loosen.
• Difficulty Attaching Bags: Ensure the side bag holder is correctly installed and not bent or misaligned. Check that the bag's mounting points are clean and free of debris.
• Unusual Noise: Inspect the holder for any contact with other motorcycle components. Ensure no cables or hoses are pinched or rubbing against the frame.

If problems persist, contact Shad customer support or a qualified mechanic.

7. Specifications

8. Warranty Information

Shad products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the official Shad website or the warranty card included with your product at the time of purchase. Keep your proof of purchase for any warranty claims.

9. Customer Support

If you require further assistance, have questions about installation, or need to report a defect, please contact Shad customer support through their official website or authorized distributors. Provide your product model number (H0CR61SE) and purchase details when contacting support.