Okin Model JLDQ.12.134.329D Actuator Motor User Manual

Introduction

This user manual provides essential information for the installation, operation, and maintenance of the Okin Refined-R Model JLDQ.12.134.329D actuator motor. This motor is designed as a replacement part for power recliners, bed motors, and lift chairs. Please read this manual thoroughly before proceeding with any installation or operation to ensure safe and correct usage.

Safety Information

Important Safety Precautions:

• Always ensure the power supply is disconnected before performing any installation, maintenance, or troubleshooting.
• Verify that the switch and power supply are functioning correctly before inspecting the motor and its connections.
• This motor is intended for indoor use only.
• Do not attempt to modify the motor or its components. Unauthorized modifications can lead to malfunction or injury.
• Ensure all connections are secure and properly seated to prevent electrical hazards.
• Keep hands and loose clothing clear of moving parts during operation.

For detailed safety guidelines, refer to the original equipment manufacturer's manual for your recliner or bed.

Product Overview and Features

The Okin Refined-R Model JLDQ.12.134.329D is a robust actuator motor designed for various furniture applications requiring linear motion. It is a direct replacement for the original Okin JLDQ 12 motor and is compatible with several other JLDQ.12.134.329 variants (E/G/J/K/L/P/Q/S/Z) with minor differences that do not affect functionality.

Figure 1: The Okin JLDQ.12.134.329D actuator motor, showing the main body and connected cables.

Figure 2: Close-up view of the motor's identification label, displaying model number JLDQ.12.134.329D and serial number Q21041092 00487.

Figure 3: Side view of the Okin JLDQ.12.134.329D actuator motor, showing its full length and mounting points.

Figure 4: The two connectors of the actuator motor: a 2-pin square plug for power supply and a 5-pin round plug for the hand control switch.

Figure 5: Visual representation of the motor's key features and dimensions, including stroke, minimum, and maximum dimensions.

Key Features:

• Composition: Consists of 1 motor and 2 connectors.
• Connectors: One 5-pin round plug with clip for the switch hand control, and one 2-pin square plug with clip for the power supply.
• Appearance: Black (PA) and silver white (aluminum) finish.
• Stroke: 333 mm, designed to move with a slide block.
• Load Capacity: Push force: 650 N, Pull force: 650 N.
• Operation Frequency: On 1 minute / Off 8 minutes.
• Speed: 29VDC SMPS, 7 seconds without load.
• Dimensions: Minimum (shrink) 134 mm; Maximum 467 mm.

Specifications

Setup and Installation

The Okin JLDQ.12.134.329D motor is designed for easy installation as a replacement unit. Before beginning, ensure you have the necessary tools (e.g., screwdriver, wrench) and that the power to the furniture is completely disconnected.

1. Disconnect Power: Unplug the furniture (recliner, bed, lift chair) from the wall outlet.
2. Access Motor: Carefully position the furniture to gain access to the existing actuator motor. This may involve tilting the furniture or removing a fabric cover.
3. Disconnect Old Motor:
   • Disconnect the 5-pin round plug from the hand control switch.
   • Disconnect the 2-pin square plug from the power supply.
   • Unbolt or unclip the old motor from the furniture frame. Note the orientation and mounting points for reinstallation.
4. Install New Motor:
   • Position the new Okin JLDQ.12.134.329D motor in the same location and orientation as the old motor.
   • Securely bolt or clip the new motor to the furniture frame. Ensure it is firmly attached and does not wobble.
5. Connect Cables:
   • Connect the 5-pin round plug of the new motor to the hand control switch. Ensure the clip engages securely.
   • Connect the 2-pin square plug of the new motor to the power supply. Ensure the clip engages securely.
6. Test Functionality: Before fully reassembling the furniture, plug it back into the wall outlet and test the motor's operation using the hand control. Ensure smooth and complete extension and retraction.
7. Final Assembly: Once confirmed operational, reassemble any covers or components that were removed.

Note: Different furniture frames may have specific requirements for actuator installation. Always refer to your furniture's original manual for precise instructions regarding motor replacement.

Operating Instructions

The Okin JLDQ.12.134.329D actuator motor operates in conjunction with your furniture's existing hand control switch and power supply. Operation is straightforward:

• Ensure the furniture is plugged into a functional power outlet.
• Use the hand control switch provided with your furniture to extend or retract the actuator. Typically, there are buttons or levers for "Up" and "Down" or "Recline" and "Return".
• Press and hold the desired button to initiate movement. Release the button to stop the movement at any point.
• Observe the motor's duty cycle: The motor is designed for intermittent operation (1 minute ON / 8 minutes OFF). Avoid continuous operation for extended periods to prevent overheating and prolong motor life.

Maintenance

Proper maintenance ensures the longevity and optimal performance of your Okin actuator motor. This motor requires minimal maintenance.

• Cleaning: Wipe the exterior of the motor and cables with a clean, damp cloth. Do not use abrasive cleaners or immerse the motor in water. Ensure the motor is dry before reconnecting power.
• Inspection: Periodically inspect the motor, cables, and connectors for any signs of wear, damage, or loose connections. Address any issues promptly.
• Lubrication: The motor is factory-lubricated and generally does not require additional lubrication. If you notice unusual friction or noise, consult a qualified technician.
• Environmental Conditions: Ensure the motor is used in a dry, indoor environment. Avoid exposure to excessive moisture, dust, or extreme temperatures.

Troubleshooting

If you encounter issues with your Okin JLDQ.12.134.329D actuator motor, refer to the following troubleshooting guide:

Important Note: If troubleshooting steps do not resolve the issue, or if you suspect a serious malfunction, discontinue use and contact a qualified technician or customer support. Do not attempt to disassemble the motor.

Warranty and Support

For information regarding warranty coverage and customer support for your Okin JLDQ.12.134.329D actuator motor, please refer to the documentation provided at the time of purchase or contact Okin customer service directly. You can often find support contact details on the manufacturer's official website or through your retailer.

Manufacturer: OKIN Refined Electric Technology Co.,Ltd

For further assistance, please visit the Okin Store on Amazon.