Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Okin 2 Button 5 Pin Power Recliner Hand Control with Indicator and Extension Cord. This remote is designed to provide seamless control for your electric lift chair or power recliner, ensuring comfort and convenience. Please read this manual thoroughly before use to ensure proper function and safety.
Safety Information
Important: Ensure the switch matches your old button plug before use. This product is intended for indoor use only. Always follow safety guidelines when handling electrical components. Disconnect power to the recliner before attempting any installation or replacement.
Product Overview
The Okin Lift Chair Remote is a wired hand control unit designed for power recliners and lift chairs. It features two buttons for controlling the chair's movement and an indicator light for operational status.
Components
- 2-Button Hand Control Unit
- 5-Pin Round Plug (90-degree L shape connector)
- Extension Cord (pre-connected)
Figure 1: The Okin 2-button 5-pin recliner remote control with its coiled cord and attached extension cord, ready for connection.
Figure 2: The Okin recliner remote control shown alongside its detachable extension cord, illustrating the separate components.
Figure 3: A detailed view of the 5-pin round plug connector, which connects the remote to the recliner's motor.
Figure 4: A close-up of the product label located on the remote control, displaying the model number 1.11.000.322.30 and electrical specifications (DC 29V 2A).
Setup and Installation
Compatibility Check
Before installation, verify that the 5-pin round plug and the 90-degree L shape connector match your existing recliner's motor connection. This remote is compatible with OKIN Single Motor systems and most common brand recliner motors that use a 5-pin connection.
Installation Steps
- Disconnect Power: Unplug your recliner from the wall outlet to ensure safety before beginning the installation process.
- Locate Existing Remote Connection: Find where your old remote control connects to the recliner's motor. This is typically a 5-pin round plug.
- Disconnect Old Remote: Carefully unplug the old remote control from the motor.
- Connect New Remote: Take the new Okin remote's 5-pin round plug and firmly insert it into the corresponding port on your recliner's motor. Ensure the 90-degree L shape connector is properly aligned.
- Secure Connection: If your recliner uses an extension cord, ensure the connection between the remote's cord and the extension cord is secure. The extension cord is pre-connected to the remote for convenience.
- Restore Power: Once the new remote is securely connected, plug your recliner back into the wall outlet.
Figure 5: The disconnected 5-pin extension cord, showing the male and female ends that connect the remote to the recliner's motor.
Figure 6: A close-up view of the securely connected extension cord, demonstrating a proper and stable connection point.
Operating Instructions
The Okin 2 Button 5 Pin Power Recliner Hand Control is straightforward to operate:
- Up Button: Press and hold the top button to extend the footrest and recline the chair. Release the button when the desired position is reached.
- Down Button: Press and hold the bottom button to retract the footrest and bring the chair back to its upright position. Release the button when the desired position is reached.
- Indicator Light: The green indicator light on the remote illuminates when the remote is active and receiving power, providing visual confirmation of operation.
Maintenance
To ensure the longevity and optimal performance of your Okin recliner remote, follow these simple maintenance guidelines:
- Cleaning: Wipe the remote control with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the electronics.
- Cable Care: Periodically inspect the cable and connectors for any signs of wear, fraying, or damage. Ensure the cable is not pinched or tangled, which could lead to internal wire damage.
- Storage: When not in use for extended periods, store the remote in a clean, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
If you encounter issues with your Okin recliner remote, try the following troubleshooting steps:
- Remote Not Responding:
- Check if the recliner is plugged into a working power outlet.
- Ensure all connections (remote to extension cord, extension cord to motor) are secure and fully inserted.
- Verify that the indicator light on the remote is illuminated when attempting to operate. If not, there might be a power issue.
- Intermittent Operation:
- Inspect the cable for any visible damage or kinks.
- Gently wiggle the connectors to see if the connection is loose.
- Wrong Plug Type:
- If the remote does not fit your recliner's port, double-check the plug type. This remote uses a 5-pin round plug.
- Refer to Figure 3 in the Product Overview section to confirm the plug type.
If these steps do not resolve the issue, please contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | Okin |
| Model Number | 1.11.000.322.30 |
| Connector Type | 5-Pin Round Plug (90-degree L shape) |
| Cable Length | 39.4 inch (remote cord) + 56.6 inch (extension cord) |
| Item Weight | 10.5 ounces |
| Package Dimensions | 8.66 x 6.46 x 1.77 inches |
| Manufacturer | OKIN Refined Electric Technology Co.,Ltd |
| First Available Date | June 3, 2021 |
Support
We stand behind our recliner chair controller and are committed to your satisfaction. If you have any questions, concerns, or require assistance with your Okin Lift Chair Remote, please do not hesitate to contact our customer service team. We are ready to help resolve any issues you may encounter.
For support, please refer to the contact information provided with your purchase or visit the official Okin website.
