Introduction
This manual provides essential instructions for the safe and effective use of your Flame King Propane Torch Kit, Model YSN340K. Please read all instructions carefully before assembly and operation. Retain this manual for future reference.
Important Safety Information
WARNING: Failure to follow these instructions could result in fire, explosion, serious injury, or death.
- Always operate the torch in a well-ventilated area.
- Keep children and pets away from the operating area.
- Wear appropriate personal protective equipment (PPE), including safety goggles, heavy work gloves, and long-sleeved clothing.
- Ensure the propane cylinder is upright and stable during use.
- Never point the torch at people, animals, or flammable materials.
- Check all connections for leaks using a soapy water solution before ignition.
- Do not use the torch near combustible liquids or vapors.
- Face the torch downwind when igniting.
- Turn off the propane supply at the cylinder valve when not in use.
- Store the torch and propane cylinder in a cool, dry, well-ventilated area, away from direct sunlight and heat sources.
- This product is for outdoor use only.
- California Proposition 65 Warning: This product can expose you to chemicals including carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- CSA Certified: This product has been tested and certified to meet specific safety and performance standards established by CSA.
Product Components
The Flame King Propane Torch Kit (Model YSN340K) includes the following components:
- Torch assembly with large wide nozzle
- Ergonomic grip handle
- Flame control knob
- Idle boost control lever (safety lever valve)
- Piezo igniter (push button)
- 10-foot propane hose with POL safety valve and handwheel tightener
Image: Detailed view of the Flame King Propane Torch Kit, highlighting the grip handle, flame control knob, idle boost control lever, piezo igniter, large wide nozzle, 10-foot hose, POL safety valve, and handwheel tightener.
Image: Close-up of the torch handle, showing the flame control valve, easy grip handle, large wide nozzle, and POL safety valve with handwheel tightener.
Setup Instructions
Your Flame King Propane Torch Kit arrives fully assembled. Follow these steps to connect it to a propane cylinder:
- Ensure all valves are closed: Before connecting, verify that the torch's flame control knob and the propane cylinder's valve are in the OFF position.
- Connect the hose to the propane cylinder: The 10-foot hose features a POL safety valve with a handwheel tightener. This fitting is reverse-threaded.
Image: Illustration demonstrating the reverse thread connection for the POL fitting to a propane tank. Remember: "Left Tight, Right Loose."
Tighten the handwheel by turning it counter-clockwise (lefty tighty) until secure. Do not overtighten.
- Check for leaks: After connecting, open the propane cylinder valve slowly. Apply a soapy water solution to all connections. If bubbles appear, close the cylinder valve immediately and re-tighten the connection. Repeat the leak test. Do not proceed if leaks are detected.
- Position the cylinder: Place the propane cylinder on a stable, level surface, ensuring it remains upright during operation. The 10-foot hose allows for flexible positioning.
Image: The Flame King Propane Torch Kit shown fully assembled, ready for connection to a propane cylinder.
Image: The torch kit is compatible with standard liquid propane cylinders, including 5lb, 10lb, 20lb, 30lb, 40lb, 60lb, and 100lb tanks. Propane cylinders are sold separately.
Operating Instructions
Follow these steps for safe ignition and operation of your propane torch:
- Prepare the area: Ensure the operating area is clear of all flammable materials and that you are wearing appropriate PPE.
- Open cylinder valve: Slowly open the propane cylinder valve. A quarter to half turn is typically sufficient for most tasks.
- Adjust flame control knob: Turn the torch's flame control knob about 1/8 of a turn to allow a small amount of propane to flow.
- Position the torch: Point the torch nozzle away from yourself, other people, and any flammable objects.
- Ignite the torch: Press the push-button piezo igniter to light the flame. If it does not ignite immediately, adjust the flame control knob slightly and try again.
Image: Step-by-step diagram illustrating the ignition process: 1. Verify all valves are closed. 2. Open cylinder valve slowly. 3. Open the torch knob about 1/8 of a turn. 4. Ensure the boost control lever is not pushed down. 5. Ignite with the push-button igniter. Important: Point the torch away from people and flammable materials before igniting.
- Adjust flame intensity: Once ignited, use the flame control knob to adjust the flame to the desired intensity. For maximum heat (340,000 BTU), fully open the knob. The idle boost control lever can be used for momentary bursts of higher flame.
- Typical Applications:
- Weed Burning: Briefly pass the flame over weeds. The goal is to heat the plant cells, not to incinerate the plant. The weeds will wilt and die within a few days.
Image: The Flame King torch being used to burn weeds growing in cracks on a paved surface.
- Melting Ice and Snow: Direct the flame onto ice or snow to melt it.
Image: The Flame King torch effectively melting a layer of snow and ice from a paved surface.
- Roofing: Use for heating and applying roofing materials.
Image: A worker using the Flame King torch for a roofing application, heating a roll of roofing material.
- Paint Removal: Heat paint to soften it for easier scraping.
Image: The Flame King torch being used to heat and remove paint from a surface, indicated by white lines on asphalt.
- Thawing Pipes/Equipment: Carefully apply heat to thaw frozen pipes or equipment, ensuring not to overheat or damage materials.
- Lighting BBQs/Flame Pits: Use to quickly ignite charcoal or wood in BBQs and flame pits.
Image: The Flame King torch igniting charcoal in a BBQ grill, demonstrating its use for starting fires.
- Weed Burning: Briefly pass the flame over weeds. The goal is to heat the plant cells, not to incinerate the plant. The weeds will wilt and die within a few days.
- To shut down: First, close the valve on the propane cylinder completely. Allow the flame to extinguish from the remaining gas in the hose. Then, close the flame control knob on the torch.
- Cool down: Allow the torch to cool completely before handling or storing.
Maintenance
Proper maintenance ensures the longevity and safe operation of your Flame King Propane Torch Kit:
- Cleaning: Keep the torch nozzle and air intake vents free from debris. Use a soft brush or cloth to clean the exterior. Do not use abrasive cleaners or solvents.
- Hose Inspection: Regularly inspect the propane hose for cuts, abrasions, cracks, or any signs of wear or damage. Replace the hose immediately if any damage is found.
- Connection Inspection: Periodically check all connections for tightness. Re-perform a leak test with soapy water if you suspect a leak or after prolonged storage.
- Storage: Disconnect the torch from the propane cylinder after each use. Store the torch in a clean, dry place, away from extreme temperatures and direct sunlight. Ensure the propane cylinder is stored separately in a well-ventilated area, away from ignition sources.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Torch does not ignite. |
|
|
| Weak or inconsistent flame. |
|
|
| Gas leak detected (hissing sound, smell of gas, or soapy bubbles). |
|
|
| Flame blows out easily. |
|
|
Product Specifications
| Feature | Detail |
|---|---|
| Model Number | YSN340K |
| Heat Output | 340,000 BTU |
| Ignition Type | Piezo Igniter (Self-Igniting) |
| Hose Length | 10 feet |
| Compatibility | Standard liquid propane cylinders (5lbs, 10lbs, 20lbs, 30lbs, 40lbs, 60lbs, 100lbs) |
| Product Dimensions | 104"L x 2.77"W x 3"H |
| Item Weight | 2.9 pounds |
| Material | Iron, Plastic PA, Brass, Rubber |
| Maximum Temperature | 2200 Degrees Fahrenheit |
| Certifications | CSA Certified |
Warranty Information
Flame King provides a 1-Year Manufacturer's Defect Warranty. The manufacturer warrants Flame King Products (except paint and finish) to be free from defects in materials and workmanship for one year from the date of purchase. Please retain your proof of purchase for warranty claims.
Customer Support
For technical assistance, warranty claims, or questions regarding your Flame King Propane Torch Kit, please visit the official Flame King website or contact their customer service department. Refer to the product packaging or the Flame King website for current contact information.
You can also visit the Flame King Store on Amazon for more product information.
