Introduction
Thank you for choosing the Lepro Solar Motion Sensor Light. This manual provides essential information for the safe and efficient use of your new solar light. Please read it thoroughly before installation and retain it for future reference.
This product features a separated solar panel and light body, connected by a 4.8-meter extension cable, allowing flexible placement. It is designed for outdoor use, offering 1000 lumens of ultra-bright, 3-sided illumination with a 360-degree adjustable angle. The light is IP65 waterproof and equipped with a motion sensor for automatic activation.
Package Contents
- Motion Sensor Light x 2
- Wall Mount Holder x 2
- Screws x 8
- Wall Plug x 8
- Instruction Manual x 1
Image: Package contents showing two light units, mounting hardware, and the instruction manual.
Setup Instructions
- Choose a Location: Select a location for the solar panel where it can receive 6-8 hours of direct sunlight daily for optimal charging. The light unit can be placed up to 4.8 meters away from the solar panel thanks to the extension cable.
- Mount the Holder: Use the provided screws and wall plugs to securely attach the wall mount holder to your desired surface.
- Attach the Light Unit: Slide the solar light unit onto the mounted holder until it clicks into place.
- Connect the Cable: Insert the cable from the solar panel into the light unit's port. Ensure a firm connection.
- Activate the Light: Locate the ON/OFF button on the back of the light unit. Press it to turn the unit ON. The light will only activate in dark environments when motion is detected.
Image: Detail of the light unit sliding into the mounting bracket.
Image: Step-by-step installation guide for the solar light.
Operating Instructions
Motion Sensor Functionality
The Lepro Solar Motion Sensor Light is designed to operate automatically. Once activated (ON position), it will:
- Charge during the day using solar energy.
- Remain off during daylight hours.
- Automatically turn on for approximately 20 seconds when motion (human or vehicle) is detected in a dark environment.
- Automatically turn off after 20 seconds if no further motion is detected.
The motion sensor has a detection range of up to 8 meters and a 120-degree angle. The light's two side panels can be rotated 360 degrees, allowing you to adjust the illumination direction and coverage area.
Image: Motion detection range and activation at night.
Image: Automatic charging during the day and 20-second illumination at night.
Adjusting Light Panels
The two side light panels can be manually rotated 360 degrees to direct light precisely where needed, providing a wide 270-degree illumination angle.
Image: Adjustable light panels and separated solar panel design.
Maintenance
Cleaning
To ensure optimal performance, periodically clean the solar panel and light surface. Dust, dirt, or debris can reduce charging efficiency and light output. Use a soft, damp cloth to wipe the surfaces gently. Avoid abrasive cleaners or harsh chemicals.
Weather Resistance
The Lepro Solar Motion Sensor Light is designed with an IP65 waterproof rating and constructed from durable ABS material, making it resistant to heat and freezing temperatures. It can safely operate in various weather conditions, including heavy rain, snow, and extreme temperatures.
Image: IP65 waterproof and weather-resistant features.
Troubleshooting
- Light does not turn on at night:
- Ensure the ON/OFF button on the back of the unit is pressed to the ON position.
- Verify the solar panel is receiving 6-8 hours of direct sunlight daily. Partial charging may occur on cloudy days, but full charge requires direct sun.
- Check if there are other strong light sources nearby. The motion sensor light is designed to activate only in dark environments.
- The internal battery might be depleted. Allow several days of full sunlight charging.
- Light stays on constantly or flashes:
- Ensure there is no continuous motion within the sensor's detection range.
- Check for any obstructions or reflective surfaces that might be triggering the sensor.
- Light output is dim:
- Clean the solar panel and light surface to remove any dirt or debris that may be hindering performance.
- Ensure the solar panel is positioned for maximum sun exposure.
- The battery may not be fully charged. Allow more time for charging in direct sunlight.
Product Specifications
| Brand | Lepro |
| Model Name | PR640004-DW-JP-2 |
| Color | Black |
| Material | ABS+GPPS (Acrylonitrile Butadiene Styrene) |
| Light Fixture Form | Wall |
| Product Dimensions | 11.1"L x 5.87"W x 4.65"H |
| Indoor/Outdoor Usage | Outdoor |
| Power Source | Solar Powered |
| Special Features | 3-sided luminescence, 1000 lumens ultra-bright, 4.8 m cable separated type, 360° angle adjustment, IP65 waterproof |
| Control Method | Push Button |
| Light Source Type | LED |
| Light Color | Daylight (6,500K) |
| Voltage | 3.7 Volts |
| Wattage | 14 watts |
| Item Weight | 1.1 pounds (500 Grams) |
| Batteries | 1 Lithium Ion battery required (included) |
| Water Resistance Level | Waterproof (IP65) |
| Brightness | 1000 Lumens |
Warranty and Support
For information regarding product warranty, please refer to the documentation included with your purchase or visit the official Lepro website. Optional protection plans may be available for purchase from third-party providers.
For customer support, technical assistance, or to view the latest user manual PDF data, please visit the Lepro Store on Amazon or contact Lepro customer service directly.