1. Introduction
Thank you for choosing the Lexicon Rowe Wood Twin Over Full Bunk Bed with Storage Boxes. This manual provides essential information for the safe assembly, operation, and maintenance of your new bunk bed. Please read all instructions carefully before beginning assembly and retain this manual for future reference.
Figure 1.1: The Lexicon Rowe Twin Over Full Bunk Bed with Storage Boxes, showcasing its dark cherry finish and integrated storage drawers.
2. Safety Information
Your safety and the safety of others are very important. Please observe all safety warnings and instructions to reduce the risk of injury.
- Adult Assembly Required: This product requires adult assembly. Ensure all parts are present and undamaged before beginning.
- Weight Limits: The top bunk supports a mattress up to 6 inches thick. Each bed holds up to 300 lbs. Do not exceed these weight limits.
- Guard Rails: The top bunk is equipped with guard rails. Always ensure guard rails are properly installed and secured.
- Ladder Safety: Use the ladder for access to the top bunk. Do not jump on or off the bunk bed.
- Mattress Thickness: For the top bunk, use only mattresses that are 6 inches thick or less to ensure proper guard rail height.
- No Foundation/Box Spring: This bunk bed is designed to be used without a foundation or box spring.
- Ventilation: Ensure adequate ventilation around the bed.
- Regular Checks: Periodically check all bolts and connections to ensure they remain tight. Retighten as necessary.
- Children's Safety: Young children should not be allowed on the top bunk. The top bunk is not suitable for children under 6 years of age.
3. Parts List
Before assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, do not proceed with assembly. Contact customer support for assistance.
- Headboard (Twin and Full sections)
- Footboard (Twin and Full sections)
- Side Rails (for both Twin and Full beds)
- Ladder
- Guard Rails (for top bunk)
- Bed Slats (for both Twin and Full beds)
- Under-bed Storage Boxes with Casters (2 units)
- Assembly Hardware (bolts, nuts, washers, etc.)
Figure 3.1: The bunk bed positioned in a room, illustrating its overall appearance and the integrated storage boxes.
4. Setup and Assembly
Assembly requires two adults. No special tools are needed as all necessary hardware is included. Follow these steps carefully:
- Unpack Components: Carefully remove all parts from the packaging. Lay them out on a soft, clean surface to prevent scratching.
- Assemble Lower Bed: Attach the side rails to the headboard and footboard of the full-size bed. Secure all connections with the provided hardware. Do not fully tighten bolts until all components are aligned.
- Install Lower Bed Slats: Place the full-size bed slats across the side rails. Ensure they are evenly spaced and secured according to the instructions.
- Assemble Upper Bed: Repeat the process for the twin-size bed, attaching side rails to the headboard and footboard.
- Install Upper Bed Slats: Place the twin-size bed slats across the upper side rails.
- Attach Upper Bed to Lower Bed: Carefully lift the assembled twin bed and align it with the designated connection points on the full bed frame. Secure with the provided hardware. This step requires two adults.
- Install Guard Rails: Attach the guard rails to the top bunk, ensuring they are firmly secured.
- Attach Ladder: Securely attach the ladder to the designated points on the bunk bed frame.
- Assemble Storage Boxes: Follow the separate instructions for assembling the two under-bed storage boxes. Once assembled, insert the casters into the base of each box.
- Final Tightening: Once all components are assembled and aligned, go back and fully tighten all bolts and connections. Do not overtighten.
Figure 4.1: Dimensional view of the bunk bed, showing overall height (65.5"), length (78"), and width (56.5").
5. Operating Instructions
Using your Lexicon Rowe Bunk Bed safely and effectively:
- Mattress Placement: Place a twin-size mattress on the top bunk and a full-size mattress on the lower bunk. Ensure the top bunk mattress does not exceed 6 inches in thickness.
- Accessing Top Bunk: Always use the provided ladder to access the top bunk. Do not climb on the frame or other furniture.
- Storage Boxes: The under-bed storage boxes are on casters for easy access. Pull them out gently to store items and push them back in when not in use. Do not overload the boxes.
- Weight Distribution: Distribute weight evenly on both bunks. Avoid concentrating weight in one small area.
6. Maintenance
Proper care will extend the life and appearance of your bunk bed:
- Cleaning: Wipe surfaces with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners, as they may damage the dark cherry finish.
- Dusting: Regularly dust the bed frame with a dry, soft cloth.
- Hardware Check: Periodically inspect all bolts, screws, and connections. Tighten any loose hardware to ensure stability and safety.
- Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause fading or damage to the wood finish.
- Humidity Control: Maintain a stable humidity level in the room to prevent wood from warping or cracking.
Figure 6.1: A close-up view of the dark cherry wood finish, highlighting its texture and color.
7. Troubleshooting
Common issues and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Bed feels wobbly or unstable. | Loose hardware. | Check and tighten all bolts and screws. Ensure all connections are secure. |
| Storage boxes do not slide smoothly. | Casters are dirty or damaged; uneven floor. | Clean casters. Check for obstructions under the bed. Ensure the floor is level. |
| Squeaking noises. | Loose connections; friction between wood parts. | Tighten all hardware. Apply a small amount of furniture wax or silicone spray to contact points if necessary. |
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | Rowe Wood Twin Over Full Bunk Bed with Storage Boxes |
| Brand | Lexicon |
| Model Number | B2013TFDC-1_T |
| Size | Twin-Full |
| Color | Dark Cherry |
| Material | Pine veneer, wood, engineered wood |
| Product Dimensions (L x W x H) | 78" x 56.5" x 65.5" |
| Item Weight | 179.25 lbs |
| Top Bunk Mattress Thickness Limit | 6 inches (maximum) |
| Weight Capacity (each bed) | Up to 300 lbs |
| Assembly Required | Yes, Adult Assembly Required |
| Foundation/Box Spring Required | No |
| Included Components | Headboard, Footboard, Side Rails, Ladder, Guard Rails, Slats, 2 Storage Boxes |
| UPC | 782359980645 |
9. Warranty Information
For detailed warranty information regarding your Lexicon Rowe Bunk Bed, please refer to the warranty card included with your purchase or visit the official Lexicon website. The warranty typically covers manufacturing defects under normal use and service.
10. Customer Support
If you have any questions, require assistance with assembly, or need to report missing/damaged parts, please contact Lexicon customer support. Refer to the contact information provided on your purchase receipt or the Lexicon official website for the most current support details.
Online Resources: For additional support and product information, visit the Lexicon website.
