1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your NIXON OFFROAD Front Bumper Assembly. This heavy-duty front bumper is designed for enhanced off-road performance and vehicle protection.
Compatibility: This front bumper is compatible with:
- 2018-2026 Jeep Wrangler JL (2-door and 4-door models)
- 2019-2026 Jeep Gladiator JT
Please read these instructions thoroughly before beginning installation to ensure proper fitment and safe operation.
2. Safety Information
Always prioritize safety during installation and use. Failure to follow safety guidelines may result in injury or damage to property.
- Wear appropriate personal protective equipment, including safety glasses and gloves.
- Ensure the vehicle is parked on a level surface with the parking brake engaged.
- Disconnect the vehicle's battery before beginning any electrical work.
- Do not attempt installation if you are unsure of any steps. Consult a qualified professional.
- Keep all fasteners tightened to specifications. Regularly check for loose hardware.
- This bumper is heavy. Seek assistance when lifting or positioning the bumper to prevent injury.
3. Package Contents
Verify that all components listed below are present and undamaged before proceeding with installation.
- NIXON OFFROAD Front Bumper Assembly
- Installation Hardware Kit (bolts, washers, nuts, wiring for fog lights if applicable)

Figure 3.1: Included installation hardware kit. Contents may vary slightly.
4. Setup and Installation
This bumper is designed for a direct bolt-on installation using factory mounting points. No drilling or cutting is typically required. Professional installation is recommended.
4.1. Preparation
- Park the vehicle on a flat, stable surface and engage the parking brake.
- Disconnect the negative terminal of the vehicle's battery.
- Remove the factory front bumper according to your vehicle's service manual. This typically involves removing several bolts and disconnecting any fog light wiring.
- Carefully unpackage the NIXON OFFROAD Front Bumper Assembly and inspect for any shipping damage.
4.2. Bumper Installation
- With assistance, carefully lift the NIXON OFFROAD Front Bumper Assembly and align it with the vehicle's frame mounting points.
- Insert the provided bolts through the bumper and frame, securing them with washers and nuts. Do not fully tighten at this stage.
- If your vehicle has OEM fog lights, relocate them into the pre-machined attachment points on the new bumper. Ensure a flush and secure fit. Connect any necessary wiring.
- Once the bumper is aligned and all bolts are in place, gradually tighten all fasteners to the manufacturer's recommended torque specifications (refer to your vehicle's service manual for frame bolt torque specs).
- Reconnect the vehicle's battery.

Figure 4.1: Front bumper assembly partially installed on a Jeep.

Figure 4.2: Close-up view of the integrated fog light housing.

Figure 4.3: Side profile of the installed front bumper.
5. Operation and Features
Your NIXON OFFROAD Front Bumper Assembly is designed with several features to enhance your off-road experience:
- Winch Plate: The integrated winch plate is capable of supporting a 12,000 lb. winch. Ensure proper installation of any winch according to its manufacturer's instructions.
- D-Ring Mounts: Heavy-duty D-ring mounts are welded both inside and out for increased strength, providing secure recovery points. D-rings are not included with this bumper.
- Fog Light Housing: Designed to accommodate OEM fog lights, allowing you to maintain factory lighting functionality and widen your field of vision during off-road driving.
6. Maintenance
To ensure the longevity and appearance of your NIXON OFFROAD Front Bumper, follow these maintenance guidelines:
- Cleaning: Regularly clean the bumper with mild soap and water to remove dirt, mud, and road grime. Avoid abrasive cleaners or harsh chemicals that could damage the powder-coated finish.
- Inspection: Periodically inspect all mounting hardware for tightness. Re-torque any loose bolts to prevent rattling or structural issues.
- Damage: Inspect the bumper for any signs of damage, such as dents, scratches, or rust. Address minor scratches with appropriate touch-up paint to prevent corrosion.
- Winch and D-Rings: If a winch or D-rings are installed, follow their respective manufacturer's maintenance instructions.
7. Troubleshooting
If you encounter issues during or after installation, consider the following common troubleshooting steps:
- Fitment Issues: Double-check that the bumper is correctly aligned with the vehicle's frame mounting points. Ensure no obstructions are preventing proper seating.
- Loose or Rattling Bumper: Verify that all mounting bolts are securely tightened to the recommended torque specifications.
- Fog Lights Not Working: Check all electrical connections for the fog lights. Ensure the vehicle's battery is properly reconnected and fuses are intact.
- Missing Hardware: Refer to the package contents list. If any hardware is missing, contact NIXON OFFROAD customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Nixon Offroad |
| Model Number | ND-NJT01A101-BX |
| UPC | 735209795708 |
| Vehicle Compatibility | 2018-2026 Jeep Wrangler JL, 2019-2026 Jeep Gladiator JT |
| Material | 5/32" Cold Rolled Solid Steel |
| Finish | Textured Black Powder-Coated |
| Item Weight | Approximately 89.42 lbs (40.56 kg) |
| Winch Plate Capacity | Up to 12,000 lbs |
| Installation Type | Direct Bolt-on |
9. Warranty and Support
NIXON OFFROAD provides the following warranty and support for this product:
- Warranty: This product is covered by a 12-month warranty from the date of purchase.
- Returns: A 30-day refund policy is available from the date of purchase.
- Customer Support: For technical assistance, warranty claims, or missing parts, please contact NIXON OFFROAD customer service through the retailer where the product was purchased or visit the official NIXON OFFROAD website.