1. Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your FibroPool FH270 Swimming Pool Heat Pump. Please read this manual thoroughly before attempting to install or operate the unit. Retain this manual for future reference.
The FibroPool FH270 is a high-efficiency, all-electric heat pump designed to heat above-ground and in-ground swimming pools and spas. It utilizes advanced heat pump technology to transfer heat from the ambient air into your pool water, offering an energy-efficient alternative to traditional gas or propane heaters.
Figure 1.1: Front view of the FibroPool FH270 Heat Pump.
2. Safety Information
Important Safety Instructions: Always follow basic safety precautions when installing and operating this electrical equipment. Failure to do so may result in serious injury, death, or property damage.
- Electrical Safety: The FH270 operates on 240 Volts. All electrical wiring must be performed by a qualified electrician in accordance with local and national electrical codes. Ensure proper grounding to prevent electrical shock.
- Water and Electricity: Never operate the heat pump if water is present around the electrical connections or if the unit appears damaged. Keep children and unauthorized persons away from the unit during operation.
- Installation: Ensure the unit is installed on a stable, level surface with adequate ventilation. Do not block air intake or exhaust. Maintain proper clearances as specified in the installation section.
- Maintenance: Disconnect all power to the unit before performing any maintenance or service. Only qualified service personnel should attempt repairs.
3. Product Overview
The FibroPool FH270 is engineered for high performance and durability. Its design incorporates key features for efficient pool heating:
- Clean Electric Power: Operates solely on electricity, eliminating the need for natural gas or propane.
- High Efficiency: Features high-pressure differential compressors and titanium heat exchangers for optimal energy transfer.
- Rugged Design: Constructed with an enamel-coated steel chassis to withstand outdoor elements.
- Easy Operation: Equipped with a digital control panel for convenient temperature management.
Figure 3.1: The FibroPool FH270 Heat Pump, highlighting its powerful electric heating capability.
The unit's compact design allows for flexible installation options. The internal components are designed for longevity and efficient heat transfer.
Figure 3.2: Detail of the high-efficiency titanium heat exchanger and radiator coils.
4. Setup and Installation
Proper installation is crucial for the performance and longevity of your FH270 heat pump. It is highly recommended that installation be performed by a certified pool professional or a qualified electrician and plumber.
4.1. Site Selection
- Choose a location outdoors with ample airflow, away from obstructions that could impede air circulation.
- Ensure the unit is placed on a solid, level surface capable of supporting its weight (approximately 160.7 lbs). Concrete pads or sturdy pavers are suitable.
- Maintain a minimum clearance of 24 inches (60 cm) around the air intake and exhaust sides for optimal performance.
4.2. Electrical Connection
The FH270 requires a dedicated 240 Volt circuit. Consult the electrical specifications on the unit's label and local electrical codes for appropriate breaker size and wiring requirements. The unit is designed for convenient installation with a 240-volt circuit.
- All electrical connections must be made by a licensed electrician.
- Ensure the power supply is disconnected at the main breaker before beginning any wiring.
- Installation parts, including wiring terminals, are located inside the service door panel. Unscrew the four Phillips screws at the corners of this panel to access them.
4.3. Plumbing Connection
The heat pump connects to your pool's filtration system. It comes with 1 1/2 inch compression fittings for easy integration.
- Connect the pool water return line to the heat pump's inlet and the heat pump's outlet to the pool's return line.
- Ensure all connections are watertight to prevent leaks.
- A bypass valve setup is recommended to control water flow through the heat pump and for maintenance purposes.
4.4. Initial Startup
- After all electrical and plumbing connections are secure, ensure your pool pump is running and water is flowing through the heat pump.
- Restore power to the heat pump at the main breaker.
- The digital control panel will illuminate. Follow the operating instructions to set your desired pool temperature.
5. Operating Instructions
The FH270 heat pump features a user-friendly digital control panel for easy temperature setting and monitoring.
Figure 5.1: The digital control panel for the FH270 heat pump.
5.1. Digital Control Panel
The control panel displays the current water temperature and allows you to set the desired temperature. It typically includes buttons for power, mode selection, and temperature adjustment (up/down arrows).
- Power On/Off: Press the power button to turn the unit on or off.
- Temperature Setting: Use the up and down arrows to adjust your desired pool water temperature. The unit will automatically heat the water to this set point.
- Mode Selection: Some models may offer different operating modes (e.g., heating only, cooling). Refer to the specific icons on your display.
The heat pump operates automatically based on the water flow. When the pool pump is running and water is flowing through the unit, the heat pump will activate if the water temperature is below the set point. It will automatically turn off once the desired temperature is reached or if water flow ceases.
6. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your FibroPool FH270 heat pump.
- Coil Cleaning: Periodically inspect the evaporator coil (the large finned area) for debris, leaves, or dirt. Clean gently with a soft brush or hose to ensure unrestricted airflow.
- Clearances: Ensure that the area around the heat pump remains clear of vegetation, debris, or any obstructions that could block airflow.
- Water Chemistry: Maintain proper pool water chemistry to prevent corrosion and scaling within the heat exchanger.
- Winterization: In colder climates where temperatures drop below freezing, proper winterization of the heat pump is essential to prevent damage. Consult a pool professional for specific winterization procedures for your region. This typically involves draining water from the unit and protecting it from the elements.
7. Troubleshooting
This section provides solutions to common issues you might encounter with your FH270 heat pump. For problems not listed here, or if solutions do not resolve the issue, contact FibroPool customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heat pump not turning on. | No power, low water flow, unit in standby. | Check circuit breaker. Ensure pool pump is running and water is flowing. Press power button on control panel. |
| Unit displays "No Flow" error. | Insufficient water flow through the unit. | Verify pool pump is operating correctly. Check for clogged skimmer baskets, pump strainer, or dirty filter. Ensure all valves are open and water lines are clear. |
| Water not heating sufficiently. | Ambient air temperature too low, pool size exceeds capacity, dirty coils, incorrect temperature setting. | Ensure ambient temperature is within operating range (above 50°F). Verify pool size is within recommended limits (up to 15,000 gallons). Clean evaporator coils. Check and adjust set temperature on control panel. Consider using a solar blanket to retain heat. |
| Unusual noises from unit. | Debris in fan, loose components, refrigerant issue. | Turn off unit and inspect fan area for obstructions. If noise persists or is unusual, contact customer support. |
8. Specifications
Key technical specifications for the FibroPool FH270 Heat Pump:
| Specification | Detail |
|---|---|
| Model | FH 270 |
| Brand | FibroPool |
| BTU Output | 70,000 BTU |
| Power Source | Corded Electric |
| Voltage | 240 Volts |
| Material | Metal (Enamel-coated steel chassis) |
| Dimensions (L x W x H) | 40 x 16 x 31 inches |
| Item Weight | 160.7 pounds |
| Compatible Pool Size (In-ground) | Up to 15,000 gallons |
| Compatible Pool Size (Above-ground) | Up to 27 foot round or 18 by 33 foot oval |
| Connection Fittings | 1 1/2 inch compression fittings |
Figure 8.1: Dimensions of the FibroPool FH270 Heat Pump.
Figure 8.2: Product specification label on the side of the unit.
9. Warranty and Support
Your FibroPool FH270 Heat Pump is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official FibroPool website.
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact FibroPool customer support. You can find contact information on the FibroPool website or through your purchase documentation.
Online Resources: For additional information and resources, visit the official FibroPool store on Amazon: FibroPool Amazon Store.
