Introduction
This manual provides essential information for the installation, operation, and maintenance of your original Krups Heineken BeerTender Lever Handle and Seals. This replacement part is designed to restore the functionality of your BeerTender beer pump, ensuring proper dispensing and preventing leaks.
Product Overview
The Krups Heineken BeerTender Lever Handle and Seals are genuine replacement components for various BeerTender models. This assembly includes the lever handle for dispensing beer and the necessary seals to ensure a tight, leak-free connection within the beer pump mechanism.
Image: The Krups Heineken BeerTender Lever Handle and Seals. This image shows the black, ergonomic lever handle with a metallic base, featuring two black O-rings at the very bottom for sealing purposes. The handle is designed for comfortable grip and precise beer dispensing.
Compatible Models:
- VB5000, VB5020, VB5100, VB5120, VB7008
- VB500000/7Z, VB5000NE/7ZA
- VB5020FR/7ZA, VB5020GR/7ZA, VB5020US/7ZA
- VB5100NE/7ZA
- VB5120ES/7ZA, VB5120FR/7ZA, VB5120US/7ZA
- VB700800/7ZA
Please verify your BeerTender model number, typically found on the identification plate located underneath the appliance, to ensure compatibility.
Setup and Installation
Replacing the lever handle and seals requires careful attention. Always ensure the BeerTender unit is unplugged and depressurized before beginning any maintenance.
- Preparation: Unplug your BeerTender unit from the power outlet. Ensure there is no beer keg currently installed or that it is depressurized if present.
- Remove Old Part: Carefully locate the existing lever handle assembly on your BeerTender. Depending on your specific model, this may involve unscrewing a retaining ring or pressing a release button. Gently pull the old lever handle and any attached seals away from the unit. Note the orientation of the old seals.
- Inspect and Clean: Inspect the area where the lever handle connects for any debris, dried beer residue, or damage. Clean thoroughly with a damp cloth and mild detergent if necessary, then dry completely.
- Install New Seals: Carefully place the new seals onto the metallic base of the new lever handle, ensuring they are correctly seated in their grooves. A small amount of food-grade lubricant (e.g., silicone grease) can be applied to the seals to aid installation and ensure a better seal, but this is optional.
- Insert New Handle: Align the new lever handle and seals with the opening on your BeerTender unit. Gently push the assembly into place until it clicks or locks securely. Ensure it is fully seated and does not wobble.
- Test Functionality: Once installed, gently operate the lever to ensure it moves freely and returns to its closed position. Reconnect the BeerTender to power and perform a leak test with a new keg (if applicable) before full use.
If you encounter any difficulty, refer to your BeerTender's main instruction manual or contact customer support.
Operating
Once the new lever handle and seals are correctly installed, the operation of your BeerTender will resume as normal. The lever is designed for smooth and controlled dispensing of beer from the keg. Pull the lever forward to dispense and push it back to stop the flow.
Maintenance
Regular maintenance of the lever handle and seals will prolong their lifespan and ensure optimal performance of your BeerTender.
- Cleaning: After each keg change or as needed, wipe down the lever handle with a damp cloth. For thorough cleaning, the lever handle can be removed (following the installation steps in reverse) and washed with warm, soapy water. Rinse thoroughly and dry completely before reinstallation.
- Seal Inspection: Periodically inspect the seals for any signs of wear, cracking, or deformation. Worn seals can lead to leaks and should be replaced promptly.
- Lubrication: If the lever feels stiff or squeaky, a small amount of food-grade silicone lubricant can be applied to the seals to ensure smooth operation.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Beer leaks from around the lever. | Damaged or improperly seated seals. | Remove the lever handle, inspect seals for damage. Replace seals if necessary. Ensure seals are correctly seated during reinstallation. |
| Lever is stiff or difficult to operate. | Lack of lubrication on seals; residue buildup. | Clean the lever and seals thoroughly. Apply a small amount of food-grade silicone lubricant to the seals. |
| Beer flow is inconsistent or weak. | Partial blockage; seals not creating proper pressure. | Ensure the lever is fully engaged. Check for any obstructions around the dispensing mechanism. Verify seals are intact and properly installed. |
Specifications
- Product Type: Replacement Lever Handle and Seals
- Brand: KRUPS
- Compatible Models: VB5000, VB5020, VB5100, VB5120, VB7008, VB500000/7Z, VB5000NE/7ZA, VB5020FR/7ZA, VB5020GR/7ZA, VB5020US/7ZA, VB5100NE/7ZA, VB5120ES/7ZA, VB5120FR/7ZA, VB5120US/7ZA, VB700800/7ZA
- Approximate Weight: 80 g (0.18 lbs)
- Material: Durable plastic (handle), metallic base, rubber seals
Warranty and Support
Information regarding specific warranty coverage for this replacement part is not explicitly available in the product details. For warranty inquiries or technical support, please contact Krups customer service or the retailer from whom the part was purchased. Always refer to the original BeerTender appliance's warranty information for overall coverage.
You can visit the official KRUPS store for more information: KRUPS Official Store
