1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of the ALLIANCE LAUNDRY SYSTEMS Output Control Board, model 202508P. This genuine OEM part is designed to control the timing and execution of component functions in compatible top-loaded washers. Adherence to these instructions is crucial for safe and effective use.
2. Safety Information
Before proceeding with any installation or maintenance, observe the following safety precautions:
- Disconnect Power: Always disconnect the appliance from all utilities (electrical, water, gas) before attempting any service or installation. Failure to do so can result in serious injury or death.
- Protective Equipment: Wear appropriate personal protective equipment, such as gloves and safety glasses, during installation.
- Qualified Personnel: Installation and service should only be performed by qualified and experienced technicians.
- Original Parts: Use only genuine OEM replacement parts to ensure proper function and safety.
- Follow Local Codes: Ensure all work complies with local electrical and plumbing codes.
3. Compatibility
The 202508P Output Control Board is compatible with various top-loaded commercial washer models from the following brands:
- Alliance Laundry Systems
- Speed Queen
- Unimac
- Ipso
- Cissel
- Huebsch
- Some Compatible Commercial Washer Models: AWNE82SP113TW01
This part replaces part number 202508.
4. Included Components
The package for model 202508P typically includes:
- 1x Output Control Board (202508P)
5. Installation
Installation of the Output Control Board requires technical knowledge and should be performed by a qualified technician. The following is a general overview and not a substitute for professional service:
- Preparation: Ensure the washer is completely disconnected from all power sources. Turn off the circuit breaker for the laundry area.
- Access the Control Board: Depending on the washer model, access to the output control board may involve removing the front panel or other access panels. Refer to your specific washer's service manual for detailed instructions on accessing the control board.
- Locate the Board: The output control board is typically located in the lower left front corner of the washer.
- Disconnect Wiring: Carefully photograph or diagram the existing wiring connections to ensure correct reassembly. Disconnect all wires connected to the old control board.
- Remove Old Board: Unscrew or unclip the old control board from its mounting.
- Install New Board: Mount the new 202508P Output Control Board in the same location.
- Reconnect Wiring: Reconnect all wires to the new board according to your diagram or photographs. Ensure all connections are secure.
- Reassemble: Reattach any panels removed during the process.
- Test: Restore power to the washer and perform a test cycle to verify proper operation.
6. Operation
The Output Control Board 202508P is an internal component that manages the operational sequences of your top-loaded washer. Once correctly installed, its function is integrated into the appliance's overall system. User interaction with the control board is indirect, through the washer's main control panel and cycle selections. If the washer exhibits unusual behavior after installation, refer to the Troubleshooting section.
7. Maintenance
The Output Control Board itself does not require routine maintenance. However, regular maintenance of the washing machine it is installed in can help prolong the life of all components, including the control board. This includes:
- Cleaning: Keep the area around the washer clean and free of dust and debris.
- Vibration Check: Periodically check for excessive vibrations during operation, which could indicate other issues.
- Professional Inspection: Consider periodic professional inspections of your appliance to identify and address potential issues early.
8. Troubleshooting
If your washer experiences issues after the installation of the 202508P Output Control Board, consider the following general troubleshooting steps:
- No Power: Ensure the washer is properly plugged in and the circuit breaker has not tripped.
- Error Codes: Consult your washer's specific service manual for explanations of any displayed error codes (e.g., "ER CO" for communication errors, as mentioned in customer reviews for similar issues).
- Incorrect Wiring: Double-check all wiring connections to the control board for proper placement and security. Loose or incorrect connections can prevent proper function.
- Component Failure: While the new board is designed to function, other components in the washer might also be faulty. A qualified technician can diagnose these issues.
- Appliance-Specific Issues: Refer to the original appliance's user manual or service guide for detailed troubleshooting specific to your washer model.
9. Specifications
| Feature | Detail |
|---|---|
| Brand Name | ALLIANCE LAUNDRY SYSTEMS |
| Model Number | 202508P |
| Item Weight | 2.26 pounds |
| Product Dimensions | 12.5 x 8 x 6 inches |
| Included Components | Output Control Board |
| Batteries Required? | No |
| ASIN | B0973PWQGP |
| Date First Available | June 11, 2021 |
10. Warranty and Support
For warranty information and technical support regarding the ALLIANCE LAUNDRY SYSTEMS Output Control Board 202508P, please refer to the documentation provided with your original appliance or contact ALLIANCE LAUNDRY SYSTEMS directly. Keep your purchase receipt as proof of purchase for any warranty claims.
