1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your SuperATV Heavy Duty Scratch Resistant Flip Windshield. Designed for 2020+ Polaris General XP 1000 and XP 4 1000 models, this windshield offers versatile weather protection and enhanced durability. Constructed from 1/4" polycarbonate, it features an XR Optic Hard Coating for superior scratch resistance, UV protection, and ease of cleaning.
Figure 1: SuperATV Flip Windshield installed on a Polaris General UTV, showing the full windshield position.
2. Safety Information
Please read and understand all safety warnings and instructions before installing or operating this product. Failure to follow these instructions may result in property damage, personal injury, or voiding of warranty.
- Always wear appropriate personal protective equipment during installation.
- Ensure the vehicle is parked on a level surface with the engine off and parking brake engaged before beginning installation.
- Verify all components are securely fastened before operating the vehicle.
- Do not operate the vehicle with the windshield in an improperly secured position.
- Legal Disclaimer: This product may contain a chemical known to the State of California to cause cancer or birth defects or other reproductive harm.
3. Components List
Before beginning installation, carefully unpack all components and compare them against the parts list provided with your product packaging. Ensure all items are present and undamaged. If any parts are missing or damaged, contact SuperATV customer support immediately.
Figure 2: Graphic illustrating 1/4 inch polycarbonate material, highlighting its thickness and durability.
4. Installation Instructions
The installation of the SuperATV Flip Windshield requires careful attention to detail. For the most accurate and up-to-date step-by-step instructions, it is highly recommended to visit the official SuperATV website and download the specific installation guide for your model (FWS-P-GENXP-RC-70).
General Installation Steps (Refer to official guide for details):
- Preparation: Clean the vehicle's roll cage and dashboard area where the windshield will be mounted. Gather all necessary tools (e.g., wrenches, drills, measuring tape).
- Bracket Attachment: Secure the mounting brackets to the vehicle's roll cage and dashboard according to the manufacturer's instructions. This may involve removing dashboard components or drilling holes.
- Windshield Mounting: Carefully position the windshield onto the attached brackets. Ensure proper alignment and fitment.
- Secure Fasteners: Tighten all bolts and fasteners to the specified torque settings. Do not overtighten.
- Functionality Check: Test the flip mechanism to ensure smooth operation and secure locking in both full and half positions.
Important Note: Some users have reported challenges with installation, particularly regarding dashboard modifications and alignment. Following the manufacturer's detailed instructions and templates is crucial for a successful installation. If you encounter difficulties, consider seeking professional assistance.
Figure 3: Close-up view of the windshield's flip mechanism and handle, located on the vehicle's dashboard.
Figure 4: Interior view of the SuperATV Flip Windshield from the driver's seat, showing the clear visibility and the handle for adjustment.
5. Operating Instructions
The SuperATV Flip Windshield offers two primary operating positions to adapt to various weather conditions and riding preferences:
- Full Windshield Position: Provides maximum protection from wind, rain, and debris. Ensure the windshield is fully closed and securely latched before driving.
- Half Windshield Position: Allows for increased airflow and a more open-air experience. To engage, unlatch the windshield and flip it down to the designated half-open position, ensuring it locks securely into place.
Always adjust the windshield while the vehicle is stationary. Do not attempt to adjust the windshield while driving.
Figure 5: Side-by-side vehicle with the SuperATV Flip Windshield in the fully closed position, providing complete protection.
Figure 6: Side-by-side vehicle with the SuperATV Flip Windshield in the half-open position, allowing for airflow.
6. Maintenance and Care
Proper care will extend the life and maintain the clarity of your SuperATV Flip Windshield, especially its XR Optic Hard Coating.
- Cleaning: Use a soft cloth or microfiber towel and a mild soap and water solution. Avoid abrasive cleaners, brushes, or harsh chemicals (e.g., ammonia-based cleaners) as these can damage the coating and polycarbonate material. Rinse thoroughly with clean water.
- Scratch Prevention: While the XR Optic Hard Coating provides exceptional scratch resistance, avoid wiping the windshield when dry or with dirty cloths, as this can still cause micro-scratches.
- Storage: When not in use for extended periods, store the vehicle in a covered area to protect the windshield from prolonged exposure to harsh elements.
7. Troubleshooting
This section addresses common issues you might encounter with your flip windshield.
- Difficulty with Installation: If you find the installation challenging, double-check the official SuperATV installation guide for your specific model. Ensure all steps are followed precisely, especially regarding drilling and alignment. Professional installation may be considered if difficulties persist.
- Gaps or Improper Fitment: Small gaps can sometimes occur. Re-check all mounting points and ensure fasteners are tightened evenly. Slight adjustments to bracket positions may be necessary. Refer to the installation guide for specific alignment tips.
- Windshield Not Flipping Smoothly: Ensure all pivot points and hinges are clean and free of debris. Check for any obstructions preventing smooth movement. Do not force the mechanism.
For issues not covered here, please contact SuperATV customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | SuperATV |
| Model Number | FWS-P-GENXP-RC-70 |
| Material | 1/4" Thick Polycarbonate |
| Coating | XR Optic Hard Coating (Scratch Resistant, UV Protective) |
| Compatibility | 2020+ Polaris General XP 1000, XP 4 1000 |
| Item Weight | 36 pounds |
| Manufacturing Origin | USA |
Figure 7: Image of the 'Made in USA' flag and text, indicating the product's manufacturing origin.
9. Warranty and Support
For information regarding product warranty, returns, or technical support, please refer to the documentation included with your purchase or visit the official SuperATV website. SuperATV is committed to providing quality products and customer satisfaction.
Contact Information: Please visit www.superatv.com for the latest contact details and support resources.
