BexGears 8 Hole Electric Guitar Pickguard (3Ply White) Instruction Manual

1. Introduction

Thank you for choosing the BexGears 8 Hole Electric Guitar Pickguard. This pickguard is designed to fit TL style electric guitars, offering both protection and a classic aesthetic. This manual provides essential information for proper installation and care of your new pickguard.

2. Product Overview

2.1 Features

• Material: 3-ply construction (white/black/white) made from durable PVC plastic.
• Screw Holes: Features 8 screw holes along the perimeter and 2 screw holes for the neck pickup.
• Protective Film: Equipped with two thin protective films on the front surface to prevent scratches during shipping and installation.
• Compatibility: Designed for TL style electric guitars.

2.2 Components Included

• 1 x BexGears 8 Hole Electric Guitar Pickguard (3Ply White)
• Pickguard mounting screws

2.3 Product Visuals

Below are images illustrating the pickguard and its construction details.

Figure 1: Front view of the BexGears 8 Hole Electric Guitar Pickguard (3Ply White) with included mounting screws.

Figure 2: Close-up view of the pickguard's edge, highlighting the 3-ply (white/black/white) construction.

3. Setup and Installation

Follow these steps to properly install your BexGears pickguard on your TL style electric guitar.

1. Prepare Your Guitar: Ensure your guitar is clean and free of dust or debris in the pickguard area. It is recommended to loosen or remove the strings for easier access.
2. Remove Old Pickguard (if applicable): Carefully unscrew and remove the existing pickguard from your guitar. Keep the old screws if you intend to reuse them, though new screws are provided.
3. Peel Protective Film: Before installation, carefully peel off the two thin protective films from the front surface of the new pickguard. This reveals the glossy finish and prevents scratches during handling.
4. Position the New Pickguard: Align the new BexGears pickguard with the screw holes and the neck pickup cavity on your guitar body. Ensure a proper fit.
5. Install Screws: Using the provided screws (or your guitar's original screws if preferred), gently screw the pickguard into place. Start with a few screws to hold it in position, then proceed to install all 8 perimeter screws and the 2 neck pickup screws. Do not overtighten the screws, as this can damage the pickguard or guitar body.
6. Final Check: Once all screws are installed, ensure the pickguard is securely fastened and there are no gaps or misalignments. Re-string your guitar if necessary.

Note on Compatibility: While designed for TL style guitars, minor variations in guitar models may exist. In rare cases, slight adjustments might be needed for a perfect fit. Please refer to the dimensional drawing for precise measurements.

Figure 3: Dimensional drawing of the pickguard, showing key measurements for fitment.

4. Maintenance

To keep your BexGears pickguard looking its best, follow these simple maintenance guidelines:

• Cleaning: Use a soft, lint-free cloth to wipe down the pickguard. For smudges or fingerprints, a slightly damp cloth with mild soap and water can be used, followed by drying with a clean, dry cloth. Avoid abrasive cleaners or solvents, as these can damage the plastic finish.
• Protection: While the pickguard is designed to protect your guitar, avoid unnecessary harsh impacts or scratches to the pickguard itself.
• Storage: If removing the pickguard for storage, keep it in a clean, dry place away from extreme temperatures or direct sunlight to prevent warping or discoloration.

5. Troubleshooting

Most issues with a pickguard are related to fitment. Here are some common points to check:

• Pickguard Does Not Align Perfectly:
• Check Model Compatibility: Ensure your guitar is a standard TL style model. Variations exist, and some guitars may have slightly different screw hole patterns or body contours.
• Compare Dimensions: Refer to the dimensional drawing (Figure 3) and compare it with your guitar's existing pickguard or body measurements.
• Minor Adjustments: For very minor misalignments, careful and gentle re-drilling of screw holes on the guitar body might be necessary. This should only be done by experienced individuals or a professional guitar technician to avoid damage.
• Scratches on Surface: Ensure you have removed both layers of the protective film. The pickguard is shipped with two films to ensure its pristine condition upon arrival.

6. Specifications

7. Warranty and Support

BexGears products are manufactured to high-quality standards. For any questions, concerns, or support needs regarding your pickguard, please contact BexGears customer service through the retailer where you purchased the product or visit the official BexGears store page on Amazon.

Amazon Store Link: BexGears Amazon Store