Introduction
This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of your hansgrohe Vernis Blend Shower Set. Please read this manual thoroughly before beginning installation or use to ensure proper function and longevity of your product.
Safety Information
WARNING:
- Always shut off the main water supply before attempting any installation or maintenance.
- Installation should be performed by a licensed plumber to ensure compliance with local codes and proper function.
- Ensure all connections are secure to prevent leaks.
- Do not use abrasive cleaners or harsh chemicals on the chrome finish, as this may damage the surface.
Package Contents
Verify that all components are present before beginning installation:
- Vernis Shape 1.5 GPM 1-Jet Showerhead
- 9-inch Showerarm
- Ecostat Square Pressure Balance Shower Trim
- Metris S Tub Spout with Diverter
Required Parts (Sold Separately)
The following part is essential for installation and must be purchased separately:
- iBox Universal Plus Rough (Model: 01850181)
Setup and Installation
hansgrohe recommends that a licensed plumber install this product to ensure correct installation and adherence to all plumbing codes.
- Prepare the Installation Area: Ensure the main water supply is turned off. Clear the wall area where the shower trim and shower arm will be installed.
- Install the iBox Universal Plus Rough: Follow the instructions provided with the iBox Universal Plus Rough (01850181) for proper in-wall installation. This rough-in valve is crucial for the functionality of your shower set.
- Install the Showerarm: Securely attach the 9-inch showerarm to the wall connection, ensuring a watertight seal.
- Attach the Showerhead: Thread the Vernis Shape 1.5 GPM 1-Jet Showerhead onto the showerarm. Hand-tighten, then use a wrench for a final quarter-turn, being careful not to overtighten.
- Install the Shower Trim: Mount the Ecostat Square Pressure Balance Shower Trim over the iBox Universal Plus Rough, following the specific instructions included with the trim kit.
- Install the Tub Spout: Attach the Metris S Tub Spout with Diverter to its connection point. Ensure it is properly sealed and aligned.
- Adjust Shower Angle: The showerhead features an adjustable angle for personalized comfort. Gently pivot the showerhead to your desired position.
Figure 1: Adjusting the showerhead angle for optimal water flow.
Operating Instructions
Your hansgrohe Vernis Blend Shower Set is designed for ease of use and a comfortable showering experience.
- Water Flow Activation: Turn the lever on the Ecostat Square Pressure Balance Shower Trim to activate water flow. Rotate the lever to adjust the water temperature.
- Diverter Function: To fill the tub, allow water to flow from the tub spout. To redirect water to the showerhead, push the valve down on the tub spout.
- Rain Shower Experience: The showerhead provides a single, luxurious Rain spray type, designed to pamper with even, lush water flow.
- Water Efficiency: This showerhead is designed to use a maximum of 1.5 gallons per minute (GPM), contributing to water conservation (EcoRight feature).
Figure 2: The XXL Performance showerhead provides broad and even water distribution.
Maintenance
Regular cleaning and maintenance will ensure the long-lasting shine and optimal performance of your hansgrohe shower set.
- Cleaning the Finish: Clean the chrome surface with a soft cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals, abrasive pads, or polishes, as these can damage the finish. Rinse thoroughly with water and dry with a soft cloth to maintain its brilliant shine.
- Limescale Removal (QuickClean): The silicone nozzles on the showerhead are equipped with QuickClean technology. Limescale deposits can be easily wiped off the nozzles with your finger or a soft cloth, restoring full spray performance.
Figure 3: Easily remove limescale from QuickClean nozzles for consistent water flow.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Low Water Pressure | Clogged showerhead nozzles; partially closed shut-off valves; low household water pressure. | Clean showerhead nozzles using QuickClean. Ensure shut-off valves are fully open. Consult a plumber if household pressure is consistently low. |
| Leaks from Connections | Loose connections; damaged O-rings or seals; improper thread sealant. | Ensure all connections are tightened correctly. Check and replace any damaged O-rings or seals. Reapply thread sealant if necessary. If issues persist, contact a licensed plumber. |
| Water Temperature Fluctuations | Issues with the pressure balance valve; hot water heater settings. | Verify hot water heater settings. If the problem persists, the pressure balance valve may require inspection or replacement by a licensed plumber. |
Specifications
- Brand: hansgrohe
- Model Number: 04963000
- Color: Chrome
- Finish Type: Chrome
- Material: Durable Plastic (Trim Plate), Plastic (Handle)
- Number of Handles: 1
- Mounting Type: Wall Mount
- Maximum Pressure: 80 psi
- Head Size: 8.375 inches
- Flow Rate: 1.5 GPM (Gallons Per Minute)
- Included Components: Showerhead, Showerarm, Shower Trim, Tub Spout
Warranty Information
hansgrohe products are manufactured to the highest quality standards. For detailed warranty information, please refer to the warranty card included with your product or visit the official hansgrohe website. Keep your proof of purchase for warranty claims.
Customer Support
If you have any questions, require technical assistance, or need to order replacement parts, please contact hansgrohe customer service. Contact details can typically be found on the official hansgrohe website or in the packaging materials.
