SPODM-2P-RD nLight SwitchPod Control User Manual

1. Introduction

1.1 Product Overview

The Sensor Switch SPODM-2P-RD nLight SwitchPod Control is a 2-button, low voltage (12/24-Vdc) wall-mount switch designed for nLight lighting control systems. This device provides manual ON/OFF control for connected lighting or other loads within an nLight network.

1.2 Key Features

• nLight SwitchPod Switch
• Wall-Mount design
• 2-Button configuration (ON/OFF for two independent circuits or functions)
• Low Voltage operation (12/24-Vdc)
• Red finish

1.3 Package Contents

• 1 x SPODM-2P-RD nLight SwitchPod Control
• Mounting Screws
• Installation Guide (this manual)

2. Safety Information

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or death.

• WARNING: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that the power is off before wiring.
• This device is designed for low voltage (12/24-Vdc) applications only. Do not connect to line voltage (120V/240V AC).
• Installation should be performed by a qualified electrician in accordance with all local and national electrical codes.
• Do not install if the product appears damaged.
• Do not modify the device in any way.

3. Setup and Installation

3.1 Tools Required

• Screwdriver (Phillips and/or Flathead)
• Wire Strippers
• Electrical Tape (optional)

3.2 Wiring Instructions

The SPODM-2P-RD uses screw terminals for connection. Ensure all connections are secure.

Figure 3.2.1: Side view of the SPODM-2P-RD with wiring label. This image shows the product's side profile, highlighting the label with detailed wiring instructions and specifications.

Figure 3.2.2: Back view of the SPODM-2P-RD. This image illustrates the rear of the switch, revealing the screw terminals where low voltage wires are connected for power and control signals.

1. Turn Off Power: Before beginning any wiring, ensure power to the circuit is turned off at the circuit breaker. Verify with a voltage tester.
2. Identify Wires:
   • WHT (White): Manual ON Input
   • BLU (Blue) stripe: Right button output
   • BLK (Black) stripe: Left button output
   • RED (Red): Power (12/24-Vdc)
   • YLW (Yellow): Common
3. Connect Wires: Connect the corresponding low voltage wires from your nLight system to the screw terminals on the SPODM-2P-RD. Ensure wires are stripped to the appropriate length and securely fastened under the screw terminals.
4. Mount Switch: Carefully push the wired switch into the wall box. Secure it using the provided mounting screws.
5. Install Wallplate: Attach the decorative wallplate (not included) over the switch.
6. Restore Power: Turn the power back on at the circuit breaker.

4. Operation

4.1 Basic Functionality

The SPODM-2P-RD features two independent push-buttons, each controlling an ON/OFF function within the nLight system. The control method is touch-based, responding to physical presses of the buttons.

Figure 4.1.1: Front view of the SPODM-2P-RD. This image displays the red faceplate with two sets of "ON" and "OFF" buttons, indicating its dual-channel control capability.

• Press the top "ON" button to activate the function associated with the upper control.
• Press the top "OFF" button to deactivate the function associated with the upper control.
• Press the bottom "ON" button to activate the function associated with the lower control.
• Press the bottom "OFF" button to deactivate the function associated with the lower control.

The specific actions triggered by these buttons are configured within the nLight system and may vary based on your installation.

5. Maintenance

The SPODM-2P-RD nLight SwitchPod Control requires minimal maintenance.

• Cleaning: To clean the surface of the switch, use a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or internal components.
• No User-Serviceable Parts: There are no user-serviceable parts inside this device. Do not attempt to open or repair the unit. Refer all servicing to qualified personnel.

6. Troubleshooting

If you experience issues with your SPODM-2P-RD, refer to the following common troubleshooting steps:

If the problem persists after attempting these solutions, contact Sensor Switch technical support or a qualified electrician.

7. Technical Specifications

8. Warranty and Support

This product is covered by the manufacturer's standard warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Sensor Switch website.

8.1 Technical Support

For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Sensor Switch customer support. Contact information can typically be found on the manufacturer's website or product packaging.

Note: The input data does not provide specific contact details or warranty duration. Please refer to the manufacturer's official resources for the most accurate and up-to-date information.