LYONGTECH MINI2-CHARGER-H

Download PDF
Contents

LYONGTECH 6-in-1 Rapid Multi Charging Hub Instruction Manual

Model: MINI2-CHARGER-H

1. Introduction

This manual provides essential information for the safe and efficient operation of your LYONGTECH 6-in-1 Rapid Multi Charging Hub. Please read these instructions carefully before use and retain them for future reference.

2. Product Overview

The LYONGTECH 6-in-1 Rapid Multi Charging Hub is designed to simultaneously charge up to four drone batteries and two 5V USB devices. It features intelligent protection mechanisms to ensure safe charging.

LYONGTECH 6-in-1 Rapid Multi Charging Hub with labeled ports

Image: Overview of the charging hub, showing four battery connect ports (8.8V/2A each) and two USB output ports (5V/3A).

3. Compatibility

This charging hub is specifically designed for the following drone batteries:

  • DJI Mini 4K
  • DJI Mini 2
  • DJI Mini 2 SE
  • DJI Mini SE

Important: This charger is NOT compatible with DJI Mavic Mini (1st generation) batteries.

Comparison of compatible DJI Mini 2 battery and incompatible Mavic Mini (1st generation) battery

Image: Visual comparison showing a DJI Mini 2 battery labeled 'Fit for' and a Mavic Mini (1st generation) battery labeled 'Not fit'.

4. Package Contents

Upon opening the package, please verify that all items are present:

  • 1 x LYONGTECH 6-in-1 Rapid Multi Charging Hub
  • 4 x Battery Charging Cables
  • 1 x AC Power Cable

Note: Batteries, remote controller, USB charging cables, and mobile phones are not included.

5. Setup

  1. Connect AC Power: Plug the provided AC power cable into the AC power port on the back of the charging hub. Connect the other end to a standard 100V-240V wall outlet.
  2. Connect Batteries: Attach the battery charging cables to your DJI Mini series batteries. Insert the other end of each cable into one of the four battery connect ports on the charging hub.
  3. Connect USB Devices (Optional): If desired, connect your remote controller or other 5V USB devices (e.g., smartphone) to the USB output ports on the side of the charging hub using appropriate USB cables (not included).
Back view of the charging hub showing AC power port and LED indicators

Image: The rear of the charging hub, highlighting the AC Power Port (100-240V 50/60Hz) and the LED indicators for charging status.

6. Operating Instructions

Once connected, the charging hub will automatically begin charging. The charging process is indicated by LED lights:

  • Red Light: Indicates that the battery is currently charging.
  • Green Light: Indicates that the battery is fully charged or no battery is connected to that port.

The hub can charge four batteries simultaneously. A full charge for four batteries typically takes approximately 70 minutes.

Diagram showing the charging hub connected to four drone batteries, a remote controller, and a smartphone

Image: An illustration demonstrating the charging hub simultaneously charging four drone batteries, a remote controller, and a smartphone, indicating a full charge time of approximately 70 minutes.

7. Safety Information

The LYONGTECH 6-in-1 Rapid Multi Charging Hub incorporates intelligent protection features to ensure safe operation:

  • Overcharge Protection
  • Over-voltage Protection
  • Over-temperature Protection
  • Short Circuit Protection

Always use the charger in a well-ventilated area and avoid covering it during operation. Do not attempt to disassemble or modify the charger.

Icons representing various safety protections of the charging hub

Image: Icons illustrating the multiple protection features of the charging hub, including over-voltage, over-current, short circuit, and over-charge protection.

8. Maintenance

  • Keep the charger clean and free from dust. Use a soft, dry cloth for cleaning.
  • Store the charger in a cool, dry place when not in use.
  • Ensure the heat dissipation holes on the bottom are not obstructed to prevent overheating. The raised pads help with air circulation.
Bottom view of the charging hub showing heat dissipation holes and raised pads

Image: The underside of the charging hub, highlighting the heat dissipation holes and raised pads designed to reduce charging temperature and prevent scratches.

9. Troubleshooting

  • Charger not powering on: Ensure the AC power cable is securely connected to both the charger and a working wall outlet.
  • Batteries not charging (no red light): Verify that the battery charging cables are properly connected to both the batteries and the charging hub ports. Ensure the batteries are compatible with this charger.
  • Slow charging: While the charger is designed for rapid charging, ensure you are using a stable power source. Charging multiple devices simultaneously may slightly extend the total charge time compared to charging a single battery.
  • Overheating: If the charger feels excessively hot, disconnect it immediately. Ensure it is in a well-ventilated area and that the heat dissipation holes are clear.

10. Specifications

BrandLYONGTECH
Model NumberMINI2-CHARGER-H
Input VoltageAC 100V-240V
Output Voltage (Battery)8.8V 8A (4 branches: 2A each)
USB Output5V 3A
Number of Ports6 (4 battery, 2 USB)
Battery Charge TimeApprox. 70 minutes (for 4 batteries)
Item Weight408 Grams

11. Warranty and Support

This LYONGTECH product comes with a 1-year manufacturer's warranty.

For technical support, warranty claims, or any questions regarding your charging hub, please contact the seller directly through the platform where you purchased the product. Ensure you have your purchase details and model number (MINI2-CHARGER-H) ready when contacting support.

© 2026 LYONGTECH. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.