Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump. This pump is designed for use in various water features, including ponds, waterfalls, and fountains, and is suitable for both submerged and inline installations. Please read these instructions thoroughly before installation and use to ensure proper function and longevity of your pump.

2. Safety Information

WARNING: To avoid possible electric shock, special care should be taken since water is used in the use of pond equipment. For each of the following situations, do not attempt repairs yourself. Return the appliance to an authorized service facility for service or discard the appliance.

• Always disconnect the pump from the power supply before handling, installing, or performing any maintenance.
• Ensure the power cord is not damaged. Do not operate the pump if the cord or plug is damaged.
• Do not remove the grounding prong from the plug.
• The pump is designed for use with a properly grounded GFCI (Ground Fault Circuit Interrupter) outlet.
• Do not use the pump for purposes other than those specified in this manual.
• Do not run the pump dry. Ensure the pump is fully submerged or adequately primed for inline use before connecting power.
• Keep children and pets away from the pump and water feature during operation and maintenance.

3. Package Contents

Verify that all components are present and undamaged:

• Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump
• Removable Pre-filter
• Multi-size Hose Adapter (for 3/4", 1", 1 1/4" tubing)
• Instruction Manual

Image: The Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump, showing the included multi-size hose adapter with indicated sizes for 3/4 inch, 1 inch, and 1 1/4 inch tubing connections.

4. Setup and Installation

4.1 Submerged Installation

1. Placement: Position the pump on a stable, level surface within your water feature. Ensure it is fully submerged in water and away from heavy debris that could clog the pre-filter.
2. Hose Connection: Attach appropriate tubing (3/4", 1", or 1 1/4" diameter) to the multi-size hose adapter on the pump's outlet. Secure with a hose clamp (not included) if necessary.
3. Electrical Connection: Route the power cord safely to a grounded GFCI outlet. Avoid kinks or damage to the cord. Do not plug in the pump until all connections are secure and the pump is fully submerged.

4.2 Inline Installation

The pump can also be used outside the water feature for inline applications, provided it is primed correctly.

1. Positioning: Place the pump on a stable, dry surface near the water source. Ensure it is below the water level of the source to facilitate priming.
2. Inlet/Outlet Connections: Connect tubing to both the inlet (side opening) and outlet (top opening) of the pump. Ensure all connections are watertight.
3. Priming: Before starting, ensure the pump housing is filled with water. This may require manually filling the inlet tubing and pump housing until water flows out the outlet.
4. Electrical Connection: Connect the pump to a grounded GFCI outlet only after it is fully primed and all connections are secure.

Image: A detailed view of the Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump, illustrating its compact design suitable for various installations.

5. Operating Instructions

1. Initial Start-up: Once the pump is installed and connected to a grounded GFCI outlet, plug it in. The pump should start immediately.
2. Adjusting Flow Rate: This pump features an adjustable flow rate. Locate the flow control lever or dial on the pump (typically near the inlet). Rotate or slide it to increase or decrease the water flow to achieve the desired effect for your water feature.
3. Monitoring: Observe the pump's operation for the first few minutes to ensure proper water flow and no unusual noises.
4. Shut-down: To turn off the pump, simply unplug it from the electrical outlet.

6. Maintenance

Regular maintenance ensures optimal performance and extends the life of your pump.

1. Disconnect Power: Always unplug the pump from the power source before performing any maintenance.
2. Clean Pre-filter: The pump is equipped with a removable pre-filter. Periodically remove the pre-filter and rinse it thoroughly under clean water to remove accumulated debris. The frequency depends on the water quality and debris level in your feature.
3. Inspect Impeller: If flow decreases or the pump makes unusual noises, the impeller may be obstructed. Remove the pump housing cover and carefully inspect the impeller for debris (e.g., leaves, string, small stones). Clean the impeller and its chamber. The ceramic shaft impellers are replaceable if damaged.
4. Winterization (for outdoor use): In freezing climates, remove the pump from the water feature before the first freeze. Clean the pump thoroughly and store it in a frost-free location, submerged in a bucket of water, or completely dry.

Image: An example of an outdoor water feature, illustrating the type of environment where the pump would be used and require maintenance.

7. Troubleshooting

8. Specifications

• Model: PB2606
• Flow Rate: 1300 Gallons Per Hour (GPH)
• Power Source: Corded Electric
• Material: Plastic
• Style: Submersible / Inline
• Color: Blue (referring to the brand's color scheme, pump itself is black)
• UPC: 852366002606

9. Warranty and Support

The Blue Thumb Large Mag-Drive 1300 GPH Fountain Pump comes with a 5-year warranty against defects in materials and workmanship. Please retain your proof of purchase for warranty claims.

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Blue Thumb customer support. You can find more information and contact details by visiting the official Blue Thumb store on Amazon: Blue Thumb Store.