Memphis Audio MJP1544

Download PDF
Contents

Memphis Audio MJP1544 15-inch MOJO Pro Car Audio Subwoofer User Manual

Model: MJP1544

1. Introduction

Thank you for choosing the Memphis Audio MJP1544 MOJO Pro Car Audio Subwoofer. This manual provides essential information for the proper installation, operation, and maintenance of your subwoofer. Please read this manual thoroughly before attempting installation or use to ensure optimal performance and safety.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the subwoofer or vehicle:

  • Professional Installation Recommended: Installation of car audio components can be complex. If you are unsure about any part of the installation process, consult a qualified professional installer.
  • Disconnect Battery: Before beginning any wiring, disconnect the vehicle's negative battery terminal to prevent electrical shorts and damage.
  • Proper Wiring: Ensure all wiring connections are secure and correctly polarized. Incorrect wiring can damage the subwoofer and amplifier.
  • Ventilation: Ensure the subwoofer enclosure has adequate ventilation to prevent overheating, especially during prolonged high-power operation.
  • Volume Levels: Prolonged exposure to high sound pressure levels can cause permanent hearing damage. Use caution when adjusting volume.
  • Secure Mounting: Always mount the subwoofer securely within the vehicle to prevent it from becoming a projectile during sudden stops or collisions.

3. Product Overview

The Memphis Audio MJP1544 MOJO Pro Subwoofer is engineered for high-performance car audio systems, delivering powerful and accurate bass reproduction. Key features include:

  • Specifically designed for high SPL (Sound Pressure Level) performance.
  • DVVC (Direct Vent Voice Coil) Cooling for enhanced thermal management.
  • Cross-drilled front plate venting.
  • Aluminum shorting ring for reduced inductance and improved sound quality.
  • Durable foam surround and rigid paper cone for robust performance.
  • Progressive spider and diecast basket for structural integrity.
  • Single-sided compression terminals for secure wiring.
Memphis Audio MJP1544 15-inch MOJO Pro Subwoofer front view

Figure 1: Front view of the Memphis Audio MJP1544 Subwoofer, showcasing the cone, surround, and Memphis Audio logo.

4. Installation Guidelines

Proper installation is crucial for the performance and longevity of your subwoofer. This section provides general guidelines. Specific enclosure design and wiring configurations may vary.

4.1 Enclosure Requirements

The MJP1544 is designed for use in a sealed or ported enclosure. Consult a car audio professional or Memphis Audio's recommended enclosure specifications for optimal performance. Ensure the enclosure is robust, airtight (for sealed), and properly braced to prevent rattles and vibrations.

4.2 Mounting

Mount the subwoofer securely into the enclosure using appropriate fasteners. Ensure the mounting surface is flat and free of obstructions. The cut-out diameter for installation is 13.84 inches, and the mounting depth is 7.88 inches.

Memphis Audio MJP1544 Subwoofer angled view showing terminals

Figure 2: Angled view of the MJP1544 Subwoofer, highlighting the single-sided compression terminals for wiring connections.

4.3 Wiring (Dual Voice Coil 4 Ohm)

The MJP1544 features a Dual Voice Coil (DVC) 4 Ohm configuration. This allows for flexible wiring options to match your amplifier's impedance requirements. Common wiring configurations include:

  • 1 Ohm Load: Wire both 4 Ohm voice coils in parallel. This configuration presents a 1 Ohm load to the amplifier.
  • 8 Ohm Load: Wire both 4 Ohm voice coils in series. This configuration presents an 8 Ohm load to the amplifier.

Always verify your amplifier's stability at the chosen impedance. Refer to your amplifier's manual for specific wiring diagrams and recommendations. Use high-quality speaker wire of appropriate gauge for the power levels involved.

Memphis Audio MJP1544 Subwoofer bottom view showing magnet structure

Figure 3: Bottom view of the MJP1544 Subwoofer, illustrating the robust magnet structure and cooling vents.

5. Operating Instructions

Once installed, follow these guidelines for optimal operation:

  • Amplifier Matching: Ensure your amplifier's RMS power output matches the subwoofer's RMS power handling (750 Watts). An underpowered or overpowered amplifier can damage the subwoofer.
  • Gain Setting: Set the amplifier gain correctly. Do not use the gain control as a volume knob. It should be set to match the output voltage of your head unit. Incorrect gain settings can lead to distortion and damage.
  • Crossover Settings: Use a low-pass filter (LPF) on your amplifier or head unit to send only low frequencies to the subwoofer. A typical LPF setting for a subwoofer is between 60Hz and 100Hz.
  • Break-in Period: Allow a break-in period of several hours of moderate listening before operating the subwoofer at maximum power. This allows the suspension components to loosen up.
  • Listen for Distortion: If you hear any distortion, rattling, or unusual noises, immediately reduce the volume. Continued operation with distortion can cause permanent damage.

6. Maintenance

The Memphis Audio MJP1544 Subwoofer requires minimal maintenance to ensure long-term performance:

  • Cleaning: Keep the subwoofer cone and surround free of dust and debris. Use a soft, dry cloth for cleaning. Avoid using harsh chemicals or excessive moisture.
  • Inspection: Periodically inspect the subwoofer for any signs of damage, such as tears in the surround or cone, loose connections, or corrosion on the terminals.
  • Enclosure Integrity: Ensure the subwoofer enclosure remains sealed and free of cracks or damage that could affect sound quality.

7. Troubleshooting

If you experience issues with your MJP1544 subwoofer, refer to the following common troubleshooting steps:

ProblemPossible CauseSolution
No Sound
  • Loose or incorrect wiring
  • Amplifier not powered on
  • Head unit settings incorrect
  • Blown fuse
  • Check all wiring connections for security and correct polarity.
  • Verify amplifier power, ground, and remote turn-on connections.
  • Ensure subwoofer output is enabled and volume is up on head unit.
  • Check fuses on amplifier and vehicle.
Distorted Sound
  • Amplifier gain set too high
  • Incorrect crossover settings
  • Overpowering the subwoofer
  • Damaged subwoofer
  • Reduce amplifier gain.
  • Adjust LPF settings.
  • Ensure amplifier RMS output matches subwoofer RMS handling.
  • Inspect subwoofer cone and surround for damage.
Weak Bass
  • Incorrect wiring (e.g., out of phase)
  • Insufficient amplifier power
  • Poor enclosure design
  • Verify correct wiring polarity.
  • Ensure amplifier is adequately powered and matched to subwoofer.
  • Check enclosure for leaks or improper volume.
Subwoofer Overheating
  • Excessive power
  • Inadequate ventilation
  • Improper impedance match
  • Reduce volume or amplifier gain.
  • Ensure enclosure and installation location allow for airflow.
  • Verify correct impedance match between subwoofer and amplifier.

8. Specifications

FeatureSpecification
Model NumberMJP1544
Subwoofer Diameter15 Inches
Voice Coil ConfigurationDual 4 Ohm (DVC 4Ω)
RMS Power Handling750 Watts
Peak Power Handling1500 Watts
Sensitivity (SENS)88 dB
Mounting Depth7.88 Inches
Cut-Out Diameter13.84 Inches
Product Dimensions (D x W x H)7.88"D x 7.88"W x 15.9"H
Item Weight30.2 pounds
Frequency Response150 Hz (Upper limit, typical for subwoofers)
Recommended UseCar Audio Music Reproduction

9. Warranty and Support

The Memphis Audio MJP1544 Subwoofer comes with a limited warranty. Please refer to the warranty card included with your product or visit the official Memphis Audio website for detailed warranty terms and conditions. Keep your purchase receipt as proof of purchase for warranty claims.

For technical support, installation assistance, or warranty inquiries, please contact Memphis Audio customer service through their official website or authorized dealer network.

© 2023 Memphis Audio. All rights reserved. Specifications are subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.