Introduction
Thank you for choosing the Relaxdays Wall Mounted Triple Soap Dispenser. This product is designed to provide a hygienic and convenient solution for dispensing liquid soap, shampoo, conditioner, or lotion in bathrooms, hotels, offices, and other facilities. This manual provides essential information for the safe and efficient use of your dispenser.
Image: The Relaxdays Triple Soap Dispenser mounted on a wall in a bathroom setting, showcasing its design and placement.
Safety Instructions
- Read all instructions carefully before installation and use.
- Ensure the dispenser is securely mounted to a stable wall surface to prevent accidental falls.
- Do not use abrasive cleaners or solvents on the dispenser, as this may damage the finish or material.
- Keep out of reach of children to prevent misuse or accidental ingestion of contents.
- Only fill with appropriate liquid soaps, shampoos, conditioners, or lotions. Do not use with granular or highly viscous substances that may clog the pump mechanism.
Package Contents
Please check that all items are present:
- 1x Relaxdays Wall Mounted Triple Soap Dispenser
- Mounting material (screws, wall plugs)
Setup and Installation
The dispenser is designed for wall mounting. Follow these steps for secure installation:
- Choose a suitable location on a solid wall surface, ensuring it is at a convenient height for use.
- Hold the dispenser's back plate against the wall at the desired mounting position.
- Mark the positions for the drill holes through the designated holes on the back plate.
- Drill holes at the marked positions using an appropriate drill bit for your wall type.
- Insert the wall plugs into the drilled holes.
- Align the dispenser's back plate with the wall plugs and secure it firmly with the provided screws.
Image: Rear view of the dispenser, highlighting the mounting points for wall installation.
Image: The dispenser securely mounted on a tiled shower wall, demonstrating a typical installation.
Operating Instructions
This dispenser features three separate compartments, each with a capacity of approximately 300 ml.
Filling the Dispenser:
- To open a compartment, lift the lid located at the top of each chamber.
- Carefully pour your desired liquid (soap, shampoo, conditioner, etc.) into the compartment. Do not overfill.
- Close the lid securely after filling.
Image: Top-down view of the dispenser with the lids open, illustrating the refill process for each chamber.
Dispensing Liquid:
- Place your hand under the nozzle of the desired compartment.
- Press the large button on the front of the compartment to dispense the liquid.
- Release the button to stop dispensing.
Image: A close-up view of the dispensing button and nozzle, showing the mechanism for liquid release.
Image: A user operating the dispenser in a shower, demonstrating the ease of access and use.
Maintenance
Cleaning:
- Regularly clean the exterior of the dispenser with a soft, damp cloth and mild soap.
- For internal cleaning, empty the compartments and rinse thoroughly with warm water. Allow to air dry completely before refilling.
- Avoid using harsh chemicals, abrasive sponges, or scouring pads, as these can scratch or damage the plastic surfaces.
Refilling:
- Refill the compartments as described in the 'Operating Instructions' section when the liquid level is low.
- Ensure the lids are properly sealed after refilling to prevent contamination or leakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dispenser not pumping liquid | Compartment is empty; Liquid is too thick; Air bubble in pump; Pump mechanism clogged. | Refill compartment; Dilute liquid if too thick; Press pump several times to prime; Clean pump mechanism. |
| Liquid leaking from dispenser | Lid not properly closed; Dispenser damaged; Overfilled compartment. | Ensure lids are securely closed; Inspect for cracks or damage; Do not overfill compartments. |
| Dispenser feels loose on wall | Mounting screws are loose; Improper installation. | Tighten mounting screws; Re-install dispenser following setup instructions carefully. |
Specifications
Detailed product specifications for the Relaxdays Wall Mounted Triple Soap Dispenser:
- Model Number: 10033717
- Color: Silver/Transparent
- Material: Plastic (ABS, PS)
- Product Dimensions (H x W x D): Approximately 16.5 x 26.5 x 8.5 cm (6.5" x 10.43" x 3.35")
- Volume per Compartment: Approximately 300 ml
- Total Liquid Volume: 900 Milliliters
- Item Weight: Approximately 600 g (1.25 pounds)
- Number of Compartments: 3
- Mounting Type: Wall Mounted
Image: The dispenser shown with key dimensions (height, width, depth) indicated for reference.
Warranty and Support
For any questions, concerns, or issues regarding your Relaxdays Wall Mounted Triple Soap Dispenser, please contact the manufacturer or your retailer. Please retain your proof of purchase for warranty claims, if applicable. Specific warranty details may vary by region and retailer.
