LaView LV-D01-S Electronic Deadbolt Lock User Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your LaView LV-D01-S Electronic Deadbolt Lock. Please read this manual thoroughly before installation and use to ensure proper function and safety. This keyless entry system offers enhanced security and convenience for your home or office.

Setup

Pre-Installation Checks

Before beginning installation, ensure your door meets the following specifications:

• Door Hole Diameter: 2-1/8 inches (54 mm)
• Backset: Adjustable to either 2-3/8 inches (60 mm) or 2-3/4 inches (70 mm)
• Door Edge Hole Diameter: 1 inch (25 mm)
• Door Thickness: 1-3/8 inches to 2 inches (35 mm to 50 mm)

Image: Diagram illustrating required door dimensions for installation, including hole diameter, backset, and door thickness.

Installation Steps

Follow these steps carefully for a successful installation. A drilling template is included in the package if needed for new door preparations.

Image: Exploded view diagram showing all components and their assembly order for the LaView smart lock.

1. Install the Latch: Ensure the latch is oriented correctly with the "UP" arrow facing upwards. Secure it with the provided strike screws. Test the deadbolt movement with a screwdriver to ensure it operates smoothly. Keep the latch in the retracted (unlocked) position.
2. Install the Exterior Assembly: Hold the exterior keypad assembly flush against the door. Carefully feed the key tailpiece and power cable through the door hole.
3. Install the Mounting Plate: Position the mounting plate on the interior side of the door, ensuring the cable passes through the rectangular slot. Secure the mounting plate with the provided screws, keeping it parallel to the door edge.
4. Connect the Cables: Make sure the cable from the exterior assembly is well-plugged into the socket of the interior PCB.
5. Install the Interior Assembly: Rotate the thumb turn on the interior assembly to the vertical and upward-facing position. Fix the interior assembly to the mounting plate and test if the latch works smoothly by turning the thumb turn.
6. Install Batteries: Keep the lock in the "unlock" status. Insert three new AA alkaline batteries into the battery pack. Stick in and hold the reset hole with the reset pin. While holding the reset pin, insert the last battery. Continue holding for about 3 seconds until you hear a beep sound. This reallocates the latch bolt to learn the door's orientation.
7. Complete Installation: Put back the battery lid to complete the installation.

Operating Instructions

Keyless Entry & User Codes

The LaView smart lock supports up to 20 unique user codes for convenient keyless entry.

Image: A user entering a code on the keypad for keyless entry, highlighting the convenience for multiple users.

• Default Master Pin Code: The default master pin code is 12345678. You will be prompted to change this for security reasons before adding any other codes.

Change Master Code

To change the master code:

1. Press ** (double asterisk).
2. Enter the default master code (12345678).
3. Press # (pound key).
4. Press 1.
5. Input your new master code.
6. Press #.
7. Input the new master code again to verify.
8. Press # to store the new master code.

Add User Code

To add a new user code:

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 2.
5. Type in the new user code.
6. Press #.
7. Type in the new user code again to verify.
8. Press # to add the new user code.

Delete User Code

To delete an unwanted user code:

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 3.
5. Type in the unwanted user code.
6. Press # to delete the userless one.

Add One-Time Code

One-time codes provide temporary access and expire after a single use.

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 7.
5. Type in the new user code.
6. Press #.
7. Type in the new user code again to verify.
8. Press # to add the one-time code.

Auto-Lock Function

The auto-lock feature automatically secures your door after a set period of inactivity.

Image: The LaView smart lock on a door with an arrow indicating the auto-lock function, which secures the door after 30 seconds.

Enable/Disable Auto-Lock

The auto-lock function is disabled by default.

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 51# to enable Auto-Lock.
5. Press 52# to disable Auto-Lock.

Set Auto-Lock Time Delay

The default auto-lock time delay is 30 seconds. You can adjust it between 10 and 99 seconds.

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 8.
5. Input the new delay time (10s-99s).
6. Press # to adjust the delay time.

Silent Mode

Silent mode disables all sound feedback from the lock.

Enable/Disable Silent Mode

Silent mode is disabled by default.

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 42# to enable Silent Mode.
5. Press 41# to disable Silent Mode.

Vacation Mode

Vacation mode provides enhanced security when you are away for an extended period. If the lock is unlocked by key or thumb turn while in this mode, it will beep for 1 minute.

1. Press ** (double asterisk).
2. Enter your new master code.
3. Press # (pound key).
4. Press 6.
5. Press # to enable Vacation Mode.

Maintenance

Battery Replacement

The lock is powered by 4 AA batteries. When the batteries are low, a low battery indicator will alert you to replace them.

Image: The keypad of the LaView smart lock displaying a low battery alert, indicating it's time for battery replacement.

Cleaning and Durability

The lock features an IP54 rating, making it weather-resistant and suitable for both indoor and outdoor use. Its metal frame ensures durability. Clean the keypad and lock body with a soft, dry cloth. Avoid abrasive cleaners or solvents.

Troubleshooting

If you encounter issues with your LaView smart lock, refer to the following common problems and solutions:

• Lock not responding to codes: Ensure batteries are not low. Re-enter codes carefully. Verify the master code and user codes are correctly programmed.
• Deadbolt not extending/retracting smoothly: During installation, ensure the latch bolt is properly aligned and moves freely. If the issue persists, perform the battery reset procedure (Step 6 in Installation) to re-calibrate the latch bolt's orientation.
• Keypad lights not illuminating: Check battery levels. Replace all four AA batteries if necessary.
• Lock beeps continuously in Vacation Mode: This indicates the lock was opened using the physical key or thumb turn. This is a security feature to alert you of entry while Vacation Mode is active.

Specifications

Warranty and Support

LaView offers professional customer service and life-time technical support for your product. For any inquiries or assistance, please refer to the contact information provided in your product packaging or visit the official LaView website. They provide 24/7 email assistance for after-sales support.