LaView LV-D01-R Electronic Deadbolt Lock User Manual

1. Introduction

This manual provides detailed instructions for the installation, programming, operation, and maintenance of your LaView LV-D01-R Electronic Deadbolt Lock. Please read this guide thoroughly before installation and use to ensure proper function and security.

Figure 1: LaView LV-D01-R Electronic Deadbolt Lock (Exterior and Interior Units)

2. Pre-Installation Checklist

Before beginning installation, ensure your door meets the following specifications:

• Door Hole Diameter: 2-1/8 inches (54 mm).
• Backset: Adjustable to either 2-3/8 inches (60 mm) or 2-3/4 inches (70 mm).
• Door Edge Hole Diameter: 1 inch (25 mm).
• Door Thickness: 1-3/8 inches to 2 inches (35 mm to 50 mm).

If drilling is required, refer to the provided cutout template in your product packaging.

Figure 2: Door Measurement and Component Diagram

3. Installation Guide

Follow these steps for a successful installation:

1. Adjust Latch (if necessary): The latch can be adjusted for 2-3/8" (60mm) or 2-3/4" (70mm) backsets. Rotate and pull the backset as instructed to extend the latch if needed.
2. Install Latch: Insert the latch into the door edge hole. Ensure the latch plate is flush with the door edge and secure with screws.
3. Install Exterior Assembly: Place the exterior keypad assembly onto the door, aligning the spindle through the latch.
4. Install Mounting Plate: Secure the interior mounting plate to the exterior assembly using the provided screws.
5. Connect Cables: Carefully connect the cable from the exterior assembly to the interior assembly.
6. Install Interior Assembly: Attach the interior assembly to the mounting plate, ensuring the thumb turn spindle engages correctly. Secure with screws.
7. Install Batteries: Insert 4 AA batteries into the battery compartment.
8. Test Operation: Test the lock with the default master code and the physical key to ensure smooth operation.

4. Programming and Operation

The default master PIN code is 12345678. For security, you will be prompted to change this code before adding any other user codes.

4.1 Change Master Code

To change the master code:

1. Press **.
2. Enter the current master code (default: 12345678).
3. Press #.
4. Press 1.
5. Press #.
6. Enter your new master code (4-10 digits).
7. Press #.
8. Re-enter your new master code to verify.
9. Press # to store the new master code.

A green indicator light confirms successful setting; a red light indicates failure.

4.2 Add User Codes

You can program up to 20 unique user codes (4-10 digits) for family and friends.

1. Press **.
2. Enter the master code.
3. Press #.
4. Press 2.
5. Press #.
6. Enter a new user code (4-10 digits).
7. Press #.
8. Re-enter the new user code to verify.
9. Press # to store the user code.

4.3 Add One-Time Codes

One-time codes are useful for temporary access and expire after a single use.

1. Press **.
2. Enter the master code.
3. Press #.
4. Press 7.
5. Press #.
6. Enter a new one-time code (4-10 digits).
7. Press #.
8. Re-enter the new one-time code to verify.
9. Press # to add the one-time code.

The one-time code will expire after unlocking the lock once.

4.4 Enable/Disable Auto-Lock

The Auto-Lock function automatically locks the door after 30 seconds of inactivity. It is disabled by default.

• To Enable Auto-Lock: Press ** + Master Code + # + 51 + #.
• To Disable Auto-Lock: Press ** + Master Code + # + 52 + #.

Figure 3: Auto-Lock Feature

4.5 Enable Vacation Mode

Vacation mode provides enhanced security when you are away. If the lock is unlocked by key or thumb turn in this mode, it will beep for 1 minute.

1. Press **.
2. Enter the master code.
3. Press #.
4. Press 6.
5. Press # to enable Vacation Mode.

To disable Vacation Mode, repeat the same steps.

4.6 Key Override

The lock includes a physical key override for manual access, especially useful if batteries are depleted.

Figure 4: Key Override for Manual Access

5. Maintenance

5.1 Battery Replacement

The lock is powered by 4 AA batteries. A low battery indicator will alert you when replacement is needed.

Figure 5: Low Battery Alert

To replace batteries, remove the interior cover, replace the old batteries with new ones, and reattach the cover.

5.2 Cleaning

Clean the lock's exterior with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish or electronic components.

6. Specifications

7. Troubleshooting

• Lock Not Responding: Check battery levels. Replace batteries if the low battery indicator is active.
• Incorrect Code Entry: Ensure you are pressing the correct sequence and the '#' key after each code entry.
• Setting Failure: If the indicator light flashes red after attempting a setting change, the operation was unsuccessful. Re-attempt the steps carefully.
• Physical Key Not Working: Ensure the key is fully inserted and turned correctly. Check for any obstructions in the keyway.
• Auto-Lock Malfunction: Verify that the Auto-Lock function is enabled (refer to section 4.4).

8. Warranty and Support

LaView offers lifetime technical support from the date of purchase. For any concerns or assistance, please contact their customer service team:

• Online Phone Calls: Monday to Friday, 9 am to 5 pm PDT.
• 24/7 Online After-Sales Email Service.

Refer to your product packaging or the official LaView website for specific contact details.