1. Introduction
The Hafele Loox5 LED 2060 Strip Light is a flexible, dimmable 12V LED ribbon designed for functional and indirect lighting applications. It is ideal for use within furniture, cabinets, and display cases, providing high-quality illumination with a high Color Rendering Index (CRI) of >90 for accurate color representation.
This manual provides essential information for the safe and correct installation, operation, and maintenance of your LED strip light.
Image 1: Hafele Loox5 LED 2060 Strip Light installed in a wooden shelf, providing accent lighting for a vase.
2. Safety Information
Please read and understand all safety instructions before installing or operating this product. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Disconnect Power: Always ensure the power supply is disconnected before performing any installation, maintenance, or troubleshooting.
- Voltage Compatibility: This LED strip operates on 12V DC. Use only with a compatible 12V LED driver (not included). Connecting to a higher voltage will damage the product.
- Indoor Use Only: The product has an IP20 rating, meaning it is protected against solid objects larger than 12.5mm but has no protection against water. Do not use in wet or damp locations.
- Cutting: Only cut the LED strip at the designated cut marks (every 1 inch / 25 mm). Cutting in other areas will damage the circuit and render that section inoperable.
- Heat Dissipation: Ensure adequate ventilation around the LED strip. Do not cover the strip with materials that could trap heat.
- Professional Installation: If you are unsure about any part of the installation process, consult a qualified electrician.
- No User Serviceable Parts: Do not attempt to open or repair the LED strip. This will void the warranty.
3. Package Contents
Verify that all components are present and undamaged upon unpacking:
- 1x Hafele Loox5 LED 2060 Strip Light (16.4 ft / 5m)
- 1x Lead Cable (approx. 2m / 78 3/4 inches)
Note: A compatible 12V LED driver is required for operation and is sold separately.
4. Setup and Installation
4.1 Preparation
- Surface: Ensure the installation surface is clean, dry, smooth, and free of dust or grease.
- Planning: Plan the exact routing of the LED strip and the location of the 12V driver. Measure the required length of the strip.
- Power Off: Disconnect power to the installation area before proceeding.
4.2 Cutting the LED Strip
The LED strip can be shortened to your desired length. Locate the designated cut marks, which occur every 1 inch (25 mm) along the strip. These marks are typically indicated by a copper pad and a scissor icon.
- Using sharp scissors, carefully cut the strip precisely on the designated cut line.
- Warning: Do not cut the strip in any other location, as this will permanently damage the circuit.
Image 2: Diagram illustrating the correct cutting points (every 1 inch / 25 mm) on the LED strip. The diagram also shows the narrow 5mm width of the strip.
4.3 Mounting the LED Strip
The LED strip features a self-adhesive backing for easy installation.
- Carefully peel off a small section of the protective liner from the back of the LED strip.
- Align the strip with your planned installation path and firmly press the exposed adhesive section onto the surface.
- Continue to peel off the liner gradually while pressing the strip firmly along its entire length to ensure good adhesion.
4.4 Electrical Connection
Connect the LED strip to a compatible 12V LED driver (sold separately).
- Connect the provided lead cable to the end of the LED strip. Ensure the connection is secure and the polarity (+ and -) is correct.
- Connect the other end of the lead cable to the output terminals of your 12V LED driver. Again, observe correct polarity.
- Connect the 12V LED driver to your main power supply according to the driver's specific installation instructions.
- Important: Ensure the 12V driver's wattage capacity is sufficient for the total length of the LED strip being used.
5. Operating Instructions
Once the Hafele Loox5 LED 2060 Strip Light is correctly installed and connected to a 12V LED driver, it can be operated.
- Power On/Off: The light will turn on when power is supplied to the 12V driver. Use the switch or control mechanism associated with your driver to turn the light on or off.
- Dimming: This LED strip is dimmable. If your 12V driver and control system support dimming, you can adjust the light intensity using the compatible dimmer switch or control unit. Refer to the instructions provided with your dimming system for specific operation.
6. Maintenance
The Hafele Loox5 LED 2060 Strip Light requires minimal maintenance.
- Cleaning: To clean the LED strip, ensure power is disconnected. Gently wipe the surface with a dry, soft, lint-free cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the strip.
- Inspection: Periodically inspect the strip for any signs of damage, wear, or loose connections. Ensure the adhesive backing remains secure.
- Repairs: There are no user-serviceable parts inside the LED strip. Do not attempt to repair it yourself. If the strip is damaged, it should be replaced.
7. Troubleshooting
If you encounter issues with your LED strip light, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strip does not light up. | No power to the 12V driver. Incorrect wiring or loose connections. Faulty 12V driver. Incorrectly cut LED strip. | Check power supply to the driver. Verify all connections (strip to lead, lead to driver) are secure and polarity is correct. Test the 12V driver with another compatible load if possible. Ensure the strip was cut only at designated marks. |
| LED strip flickers or is too dim. | Insufficient power from the 12V driver. Driver wattage capacity too low. Dimmer setting too low or incompatible dimmer. | Check input voltage to the driver. Ensure the driver's wattage rating exceeds the total wattage of the LED strip. Adjust dimmer setting. Confirm dimmer compatibility with 12V LED products. |
| Only a section of the LED strip lights up. | Damage to the circuit in the unlit section. Incorrect cut. | The damaged section may need to be replaced or removed. Ensure cuts are made only at designated points. |
If the problem persists after attempting these solutions, please contact Hafele customer support.
8. Specifications
Detailed technical specifications for the Hafele Loox5 LED 2060 Strip Light:
- Model: Loox5 LED 2060
- Voltage: 12 V DC
- LEDs per Meter: 120
- Total Length: 16.4 ft (5 m)
- Width: 3/16 inches (5 mm)
- Height: 1/16 inches (1.3 mm)
- Light Color: Cool White 5000 K
- Dimmable: Yes
- Color Rendering Index (CRI): >90
- Life Time: L80/B10 >50000 hours
- Power Consumption per Meter: 4.8 W
- Energy Efficiency Class: A+
- IP Code: IP20 (Indoor Use Only)
- Cuttable Interval: Every 1 inch (25 mm)
- Lead Cable Length: 78 3/4 inches (2 m)
- Certifications: UL Certified
- Material: Vinyl, Metal, PCB
8.1 Light Output Performance (5000K)
Image 3: Light output chart indicating Lux levels at different distances (250mm, 500mm, 750mm, 1000mm) for various color temperatures, including 5000K.
9. Warranty and Support
For detailed warranty information, product registration, or technical assistance, please visit the official Hafele website or contact Hafele customer service directly. Keep your purchase receipt as proof of purchase.