Jeep Fold Fat E-Bike FR 7020 Instruction Manual

1. Introduction

Welcome to the Jeep Fold Fat E-Bike FR 7020 instruction manual. This document provides essential information for the safe and efficient use of your new electric bicycle. Please read this manual thoroughly before operating the e-bike to ensure proper assembly, operation, and maintenance. Keep this manual for future reference.

2. Safety Information

Your safety is paramount. Failure to follow these safety guidelines may result in serious injury or damage to the e-bike.

2.1 General Safety

• Always wear a helmet that meets local safety standards.
• Obey all local traffic laws and regulations.
• Perform a pre-ride inspection before each use.
• Do not ride under the influence of alcohol or drugs.
• Be aware of your surroundings and ride defensively.
• Ensure all fasteners are tightened before riding.

2.2 Battery Safety

• Use only the charger provided with your e-bike.
• Do not expose the battery to extreme temperatures or direct sunlight.
• Do not puncture, drop, or disassemble the battery.
• Charge the battery in a well-ventilated area, away from flammable materials.
• If the battery is damaged or leaking, contact customer support immediately.

2.3 Riding Safety

• Familiarize yourself with the e-bike's controls, especially the brakes and pedal assist system, before riding in traffic.
• Adjust the seat height for comfortable and safe riding.
• Be cautious when riding in wet conditions, as braking distance will increase.
• Avoid riding on rough terrain or performing stunts that could damage the bike or cause injury.

3. Package Contents

Upon unpacking, please verify that all components are present:

• Jeep Fold Fat E-Bike FR 7020
• Rechargeable Lithium-ion Battery (integrated)
• Battery Charger
• User Manual
• Tools for minor assembly (if applicable, not explicitly listed but common)

4. Assembly and Initial Setup

Your Jeep Fold Fat E-Bike FR 7020 is delivered approximately 99% pre-assembled and fully charged. Minor adjustments and unfolding are required before first use.

4.1 Unfolding the E-Bike

1. Place the folded e-bike on a stable surface.
2. Release the frame folding mechanism. This is a double-secured mechanism for safety.
3. Carefully unfold the main frame until it locks into place. Ensure the locking mechanism is fully engaged and secured.
4. Unfold the handlebars and secure the handlebar stem locking mechanism.
5. Adjust the seat post to your desired riding height and secure it with the quick-release lever.
6. Ensure pedals are properly installed or unfolded if they are foldable.

Image: The Jeep Fold Fat E-Bike FR 7020 in its folded state, showing its compact dimensions (Length: 85 cm, Width: 60 cm, Height: 70 cm).

Image: Close-up view of the double-secured folding mechanism on the e-bike frame, ensuring stability when unfolded.

4.2 Battery Installation and Initial Charge

The 36V battery is integrated into the aluminum frame and is removable for charging. It comes pre-charged.

• To remove the battery, unlock it using the provided key.
• The battery can be charged while integrated into the bike or separately.
• Connect the charger to the battery charging port and then to a power outlet.
• A full charge from zero to 100% takes approximately 4 hours.
• The display will show the battery charge level.

Image: The integrated battery, showing its removable design and key lock for security and separate charging.

4.3 Pre-Ride Checks

• Tires: Check tire pressure. The 20-inch fat tires should be inflated to the recommended pressure (usually indicated on the tire sidewall).
• Brakes: Test both front and rear disc brakes to ensure they are functioning correctly.
• Handlebars and Seat: Ensure they are securely tightened and at a comfortable height.
• Folding Mechanisms: Confirm all folding mechanisms are fully locked and secured.
• Lights: Check that the front and rear lights are working.

5. Operating Instructions

5.1 Powering On/Off and Display Functions

The e-bike features an LCD color display that provides essential riding information.

1. Power On: Press and hold the power button on the display unit.
2. Display Information: The high-contrast LCD screen shows battery charge level, assistance level, current speed, trip distance, and total mileage.
3. Lights: A long press on the '+' symbol on the display unit will turn the lights on or off.
4. USB Port: The display unit includes a USB port for charging mobile devices.
5. Power Off: Press and hold the power button to turn off the e-bike system.

Image: The LCD color display mounted on the handlebars, showing speed, battery level, and total kilometers.

5.2 Pedal Assist System (PAS)

The 250W rear motor provides 5 levels of assistance, with a torque of 40 Nm, supporting speeds up to 25 km/h.

• Use the '+' and '-' buttons on the display to select your desired assistance level (1-5).
• Level 1 provides minimal assistance, while Level 5 provides maximum assistance for easier pedaling, especially on inclines.
• The motor assistance activates when you start pedaling and stops when you cease pedaling or apply the brakes.

5.3 Gear Shifting

Your e-bike is equipped with a Shimano 7-speed derailleur system.

• Use the thumb shifter on the right handlebar to change gears.
• Shift to lower gears (smaller numbers) for easier pedaling on hills or against headwinds.
• Shift to higher gears (larger numbers) for faster speeds on flat terrain.
• Always pedal lightly when shifting gears to ensure smooth transitions and prevent damage to the drivetrain.

Image: Close-up of the Shimano 7-speed thumb shifter located on the right handlebar for easy gear changes.

Image: View of the Shimano 7-speed derailleur and chain system on the rear wheel, part of the e-bike's drivetrain.

5.4 Braking

The e-bike is equipped with manual disc brakes on both the front and rear wheels.

• The left lever controls the rear brake, and the right lever controls the front brake (standard configuration, may vary by region).
• Apply both brakes simultaneously for effective and controlled stopping.
• Avoid sudden, hard braking, especially with the front brake, to prevent skidding or loss of control.

Image: Close-up of the front disc brake assembly, highlighting the braking mechanism for reliable stopping power.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your e-bike.

6.1 Cleaning

• Clean the e-bike regularly with a damp cloth and mild soap. Avoid high-pressure washers.
• Do not spray water directly onto electrical components (motor, battery, display).
• Dry the bike thoroughly after cleaning.

6.2 Tires

• Check tire pressure before each ride. Maintain pressure within the range indicated on the tire sidewall.
• Inspect tires for wear, cuts, or embedded objects.

Image: Close-up view of the 20-inch fat tire, highlighting its tread pattern and robust design.

6.3 Brakes

• Regularly check brake pads for wear and replace them when necessary.
• Ensure brake levers are firm and responsive. Adjust cable tension if needed.
• Inspect brake rotors for damage or excessive wear.

6.4 Drivetrain (Chain and Gears)

• Keep the chain clean and lubricated to ensure smooth shifting and prevent wear.
• Check the derailleur for proper alignment and adjustment.

6.5 Fasteners

• Periodically check all bolts, nuts, and quick-release levers for tightness.
• Pay special attention to the folding mechanisms, wheel axles, and handlebar stem.

6.6 Storage

• Store the e-bike in a cool, dry place, away from direct sunlight and extreme temperatures.
• If storing for an extended period, charge the battery to 50-70% and recharge every 1-2 months to maintain battery health.

7. Troubleshooting

This section addresses common issues you might encounter with your e-bike.

8. Specifications

Key technical specifications for the Jeep Fold Fat E-Bike FR 7020:

Image: The Jeep Fold Fat E-Bike FR 7020 in its unfolded state, showing its full length (174 cm) and maximum height (133 cm).

9. Warranty and Support

For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for warranty claims.

For technical support, spare parts, or service inquiries, please contact Jeep E-Bikes customer service or your authorized dealer. Provide your model number (FR 7020) and purchase date when contacting support.