XtremepowerUS 16" Sand Filter Swimming Pool Pump Manual

1. Product Overview

The XtremepowerUS 16" Sand Filter Swimming Pool Pump is designed to provide efficient and reliable filtration for above-ground swimming pools. This integrated system combines a powerful pump with a durable sand filter tank, ensuring clear and clean pool water with minimal effort.

Key features include a 16-inch tank capable of holding 110 pounds of sand, suitable for pools up to 15,000 gallons. The system is engineered for optimum filtration, consistent performance, and efficient backwashing. It features a user-friendly 4-way multi-port valve and a built-in timer for automated operation, all designed for low noise and energy efficiency.

Figure 1.1: The XtremepowerUS 16" Sand Filter and Pump system installed next to an above-ground pool.

2. Safety Information

Please read and understand all safety warnings and instructions before installing, operating, or performing maintenance on this product. Failure to follow these instructions could result in serious injury or property damage.

• Always disconnect power to the pump before performing any service or maintenance.
• Ensure the pump is installed on a solid, level surface to prevent vibration and movement.
• Do not operate the pump if the electrical cord or plug is damaged.
• Keep children and pets away from the pump and filter system during operation.
• Refer to the warning labels on the product for specific safety guidelines.
• Properly ground the pump to prevent electrical shock.

Figure 2.1: The system is safety and quality certified, ensuring adherence to safety standards.

3. Components List

Before beginning installation, ensure all components are present and undamaged:

• Sand Filter Tank (16-inch)
• Pool Pump (3/4 HP) with Timer
• 4-Way Multi-Port Valve
• Hoses and Clamps for connections
• Pressure Gauge
• Base for pump and filter

Figure 3.1: Overview of the sand filter and pump unit, highlighting its dimensions (25" W x 19" L x 29" H) and 3/4 HP power.

4. Setup and Installation

The XtremepowerUS sand filter pump is designed for quick and simple installation, typically taking less than 5 minutes for initial setup.

1. Positioning: Place the filter and pump unit on a firm, level surface near your above-ground pool. Ensure it is within reach of a grounded electrical outlet.
2. Sand Filling: Carefully fill the sand filter tank with the recommended amount of pool filter sand (approximately 110 pounds for the 16-inch model). Ensure the standpipe is centered during this process.
3. Multi-Port Valve Installation: Attach the 4-way multi-port valve to the top of the sand filter tank. Secure it firmly according to the instructions provided with the valve.
4. Hose Connections: Connect the hoses from your pool's skimmer and return lines to the appropriate ports on the multi-port valve and pump. Use the provided clamps to ensure secure and leak-free connections.
5. Pump Connection: Connect the pump to the multi-port valve. The pump is a capacitor start type and comes with a standard 3-prong plug.
6. Electrical Connection: Plug the pump into a properly grounded 115 Volt electrical outlet.

For a visual guide on the setup process, please refer to the video below:

Figure 4.1: Detail of a secure hose connection to the multi-port valve, essential for proper system function.

5. Operating Instructions

The 4-way multi-port valve allows for various operational modes to manage your pool's filtration and maintenance needs.

5.1 Multi-Port Valve Functions:

• FILTER: This is the standard operating mode for daily filtration. Water is pumped through the sand filter, trapping debris, and returned to the pool.
• BACKWASH: Used to clean the sand filter. Water flows in reverse through the filter, flushing trapped debris out through the waste port. Perform backwashing when the pressure gauge reading increases by 8-10 PSI above its clean operating pressure.
• RINSE: Used after backwashing to flush out any remaining dirty water from the valve and lines before returning to FILTER mode.
• RECIRCULATE: Circulates water through the pool without passing it through the filter. Useful for distributing chemicals quickly.
• WASTE: Drains water directly from the pool through the waste port, bypassing the filter. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
• CLOSED: Shuts off all flow to the filter and pump. Use this setting when performing maintenance or cleaning the pump strainer basket.
• WINTER: Prepares the system for winter storage, typically used for draining the filter.

Figure 5.1: Detailed diagram of the multi-port valve, showing its seven essential functions for comprehensive pool maintenance.

5.2 Timer Operation:

The pump features a built-in 24-hour timer for energy-saving performance. You can set the pump to run for specific durations (2h, 4h, 6h, 8h, 10h, 12h, 16h, 24h) to optimize filtration cycles and reduce energy consumption.

Figure 5.2: The pump's control panel with the 24-hour customizable timer, allowing users to schedule filtration cycles for energy efficiency.

Figure 5.3: A closer look at the timer settings on the pump, indicating various operational durations.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your sand filter pump.

• Backwashing: Backwash the filter regularly, typically when the pressure gauge indicates an increase of 8-10 PSI from its clean operating pressure, or when water clarity decreases. Follow the BACKWASH and RINSE procedures on the multi-port valve.
• Strainer Basket Cleaning: Periodically check and clean the pump's strainer basket to remove large debris that could impede flow. Ensure the pump is OFF and unplugged before opening the strainer lid.
• Sand Replacement: Pool filter sand typically needs to be replaced every 3-5 years, depending on usage and water quality.
• Winterizing: Before freezing temperatures, ensure the system is properly drained and winterized according to the "WINTER" setting on the multi-port valve and general pool winterization guidelines.

7. Troubleshooting

If you encounter issues with your sand filter pump, refer to the common problems and solutions below:

8. Specifications

• Brand: XtremepowerUS
• Model Number: 75131-V1
• Tank Size: 16 inches
• Sand Capacity: 110 pounds
• Recommended Pool Size: Up to 15,000 gallons
• Pump Horsepower: 3/4 HP
• Flow Rate: 3,100 Gallons Per Hour (GPH)
• Voltage: 115 Volts
• Material: Polyethylene (PE)
• Item Weight: 30 Pounds
• Overall Dimensions (L x W x H): 25" x 19" x 29"
• UPC: 840166513347

Figure 8.1: The system's powerful filtration capabilities, indicating suitability for pools up to 18,000 gallons and a flow rate of 3100 GPH.

9. Warranty and Support

For warranty information, technical support, or replacement parts, please contact XtremepowerUS customer service. Keep your purchase receipt and model number handy for faster service.

You can also refer to the official User Manual (PDF) for additional details and diagrams:

Download User Manual (PDF)