Introduction
This user manual provides comprehensive instructions for the safe and effective operation and maintenance of your veicomtech Dual Ionic Foot Bath Detox Machine. Please read this manual thoroughly before first use and retain it for future reference.
Safety Information
Adhering to these safety guidelines is crucial for preventing damage to the device and ensuring user safety:
- Do not add excessive salt to the water. Over-concentration can cause the machine to beep and enter standby mode.
- If the machine beeps, immediately replace the water and clean the arrays.
- When adding salt, do so gradually and monitor the 'A:' readings on the display. Maintain a working value between 0.4-2.5.
- Ensure all connections are secure before powering on the device.
- Keep the machine and all electrical components away from direct water contact, except for the arrays designed for immersion.
- Statements regarding dietary supplements have not been evaluated by the FDA and are not intended to diagnose, treat, cure, or prevent any disease or health condition. This product is not a medical device.
Setup Guide
Follow these steps to set up your Dual Ionic Foot Bath Detox Machine for first use:
- Unpack Components: Carefully remove all items from the packaging. Verify that all components are present: the main unit, two ionic arrays, two waist belts, and power cable.
Figure 2: All components included with the foot bath detox machine. - Connect Power: Insert the power cable into the power interface at the back of the main unit.
Figure 3: Power interface and USB interface located at the rear of the main unit. - Connect Arrays: Plug each ionic array into the "ARRAY" port on the front panel of the main unit. The machine supports dual-person use.
Figure 4: The machine is designed for dual person use, with dedicated ports for two arrays and two waist belts. - Connect Waist Belts (Optional): If using the far infrared waist belts, plug them into the "waist belt" ports.
- Prepare Foot Basin: Fill a suitable foot basin with water. The machine is compatible with various basin types.
Figure 5: The machine can be used with various types of foot basins. - Initial Setup Video: For a visual guide on setting up the machine, please watch the following video:
Video 1: A short demonstration of the initial setup and components of the VEICOMTECH Foot Spa Detox machine.
Operating Instructions
Once set up, follow these steps to begin your ionic foot bath session:
- Power On: Plug the power cable into a wall outlet and press the power switch on the back of the unit.
- Place Feet and Array: Place your feet into the prepared foot basin. Submerge the ionic array in the water alongside your feet.
Figure 6: A user enjoying a foot spa session, demonstrating typical usage. 
Figure 7: The dual functionality allows for shared foot spa leisure. - Wear Wrist Strap (Optional): If desired, wear the wrist strap connected to the machine. Ensure it makes good contact with your skin.
- Select Mode: Use the "A Mode" or "B Mode" buttons to cycle through the available operating modes (1 to 5). Each mode has a different positive/negative ion balance.
- Set Time: Use the "A Time" or "B Time" buttons to adjust the session duration. The time can typically be set from 10 to 60 minutes.
- Add Salt: Gradually add a small amount of salt to the water to increase conductivity. Monitor the 'A:' reading on the display; it should be between 0.4-2.5. Do not add too much salt at once.
- Start Session: Press the "ON/OFF" button to start the ionic foot bath session.
Figure 8: Observe the water color change during the ionic detoxification process, indicating activity. 
Figure 9: The ionic array releases positive and negative ions into the water during operation. - Comprehensive Operation Video: For a detailed guide on operating the machine, including mode and time selection, and salt addition, please watch this video:
Video 2: A comprehensive guide to setting up and operating the Dual Foot Detox Machine, including mode selection and salt addition.
- Using the Far Infrared Heating Belt:
The far infrared heating belt provides additional comfort and can be used simultaneously with the foot bath. To use:
- Wrap the belt around your waist and secure it comfortably.
- Plug the belt into the designated "waist belt" port on the main unit.
- Use the "A Belt" or "B Belt" button to select the desired temperature level (Low, Medium, High).
Video 3: Instructions on how to properly use the Far Infrared (FIR) heating belt with the detox machine.
Maintenance and Care
Proper maintenance ensures the longevity and optimal performance of your device:
- Cleaning Arrays: After each use, thoroughly clean the ionic arrays with water to remove any residue. Ensure they are dry before storage.
- Cleaning Main Unit: Wipe the main unit with a soft, damp cloth. Do not use abrasive cleaners or immerse the unit in water.
- Storage: Store the machine and its components in a cool, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
If you encounter issues with your veicomtech Dual Ionic Foot Bath Detox Machine, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine beeps and shuts down to standby. | Excessive salt concentration in the water. | Replace the water in the basin. Wash the arrays. Add salt stepwise, ensuring the 'A:' reading remains within the working value of 0.4-2.5. |
| No power. | Power cable not properly connected or power switch off. | Ensure the power cable is securely plugged into both the machine and the wall outlet. Check that the power switch on the back of the unit is in the 'ON' position. |
| No ionic activity (no bubbles, no water color change). | Insufficient salt in water or array not properly submerged. | Gradually add more salt to the water while monitoring the 'A:' reading. Ensure the array is fully submerged and making good contact with the water. |
Product Specifications
| Feature | Detail |
|---|---|
| Brand | veicomtech |
| Model | B09287WNDP |
| Product Dimensions | 15 x 11 x 4 inches |
| Item Weight | 15.1 Pounds |
| Power Source | Corded Electric |
| Material | Aluminum, Metal |
| Color | White, Black |
| Manufacturer | veicomtech |
Warranty and Support
For information regarding product warranty, returns, or technical support, please contact the manufacturer, veicomtech, directly. Refer to the product packaging or the seller's information on the purchase platform for specific contact details.
