FADINI NYOTA 115 EVO Sliding Gate Motor Instruction Manual

1. Introduction

The FADINI NYOTA 115 EVO is a robust electromechanical gearmotor designed for the automatic opening and closing of sliding gates. This manual provides essential information for the proper installation, operation, and maintenance of the device. It is intended for qualified personnel responsible for the installation and servicing of the gate automation system.

The NYOTA 115 EVO features a powerful bronze-steel coupling in an oil bath, supported by high-quality ball bearings, ensuring durability and reliability. It incorporates an encoder for continuous monitoring of gate movement, obstacle detection, and automatic reversal, enhancing safety. An electronic brake and controlled slowdown during opening and closing cycles further contribute to its smooth and secure operation.

This model is available in single-phase and three-phase versions, with power options of 0.5 HP (for gates up to 1,250 kg) and 1.0 HP (for gates up to 1,850 kg). It comes with an integrated Elpro 12 EVO electronic control unit or can be connected to an external Elpro 37/37 DS unit.

2. Important Safety Information

WARNING: Incorrect installation or improper use of this product can lead to serious injury or damage. Always follow these instructions carefully.

2.1 General Safety Warnings

• This manual is intended for qualified technical personnel. All installation, maintenance, and repair operations must be performed by authorized and competent individuals.
• Installation must comply with all local, national, and European safety regulations and standards (e.g., EN 13241, EN 12453, EN 12445).
• FADINI is not responsible for any damage or injury resulting from improper installation, incorrect use, or failure to follow the instructions in this manual.
• Do not modify any part of the product. Unauthorized modifications can compromise safety and void the warranty.

2.2 Before Installation

• Carefully inspect the product for any damage during transport. Do not install damaged components.
• Ensure the gate structure is sound, properly balanced, and moves freely without excessive friction.
• Verify that the electrical supply matches the requirements specified on the product label (single-phase, 0.5 HP or 1.0 HP).
• Install all necessary safety accessories, such as photocells, safety edges, and warning lights, to ensure safe operation in both public and private environments.

2.3 System Operation Warnings

• Regular maintenance is essential for the safe and correct functioning of the gate automation system.
• Only use original FADINI spare parts for repairs and replacements.
• Keep children and pets away from the gate area, especially during operation.
• Do not attempt to stop a moving gate by hand.
• In case of malfunction, disconnect power and contact qualified service personnel.

3. Product Overview

3.1 Key Features

• Electromechanical Gearmotor: Designed for sliding gates up to 1,850 kg.
• Oil Bath Lubrication: Bronze-steel coupling fully immersed in oil for enhanced durability and smooth operation.
• Integrated Control Unit: Equipped with Elpro 12 EVO for precise control.
• Safety Encoder: Monitors gate movement, detects obstacles, and reverses direction for safety.
• Electronic Brake: Ensures precise stopping and prevents gate overrun.
• Slowdown Function: Controlled deceleration during opening and closing cycles.
• Manual Release: Coded key release handle for manual operation during power outages.
• Durable Construction: Entire structure and cover made from painted die-cast aluminum.

3.2 Components

The FADINI NYOTA 115 EVO system typically includes:

• NYOTA 115 EVO Gearmotor with integrated Elpro 12 EVO control unit.
• Coded key for manual release.
• Mounting hardware (not always included, check packaging).
• Instruction manual (this document).

Image 3.1: Overview of the FADINI NYOTA 115 EVO electromechanical sliding gate opener, highlighting the magnetic limit switch. This image shows the main unit with its protective casing and the gear mechanism.

Image 3.2: Side view of the FADINI NYOTA 115 EVO motor, showcasing the robust gear mechanism that drives the sliding gate. The grey and black casing protects the internal components.

4. Setup and Installation

Detailed installation instructions, including electrical connections, mechanical mounting, and initial programming of the Elpro 12 EVO control unit, are provided in the comprehensive installation manual.

IMPORTANT: Installation must only be carried out by qualified and authorized personnel, strictly adhering to all applicable safety standards and regulations. Refer to the official FADINI installation manual for complete instructions.

You can find the official installation manual here (PDF).

Image 4.1: The cover page of the FADINI NYOTA 115 EVO instruction manual, indicating its content for electromechanical sliding gate openers. This document contains detailed setup and installation procedures.

5. Operating Instructions

5.1 Automatic Operation

Once installed and configured by qualified personnel, the FADINI NYOTA 115 EVO operates automatically. The gate can be opened or closed using a remote control, push button, or other access control devices connected to the Elpro 12 EVO control unit.

• Press the designated button on your remote control or access device to initiate gate movement.
• The gate will open or close, slowing down at the end of its travel.
• The integrated encoder continuously monitors for obstacles. If an obstacle is detected, the gate will stop and reverse direction to prevent damage or injury.

5.2 Manual Release (Emergency Operation)

In case of a power outage or system malfunction, the gate can be operated manually using the coded key release mechanism.

1. Locate the manual release handle on the motor unit.
2. Insert the coded key into the lock and turn it to disengage the motor.
3. The gate can now be moved manually.
4. To re-engage the motor, reverse the key turning action until the mechanism locks into place. Ensure the gate is fully closed or open before re-engaging.

CAUTION: Always ensure the gate is stationary before attempting manual release. Keep hands and clothing clear of moving parts.

6. Maintenance

Regular maintenance is crucial for ensuring the long-term reliability and safe operation of your FADINI NYOTA 115 EVO gate motor. All maintenance procedures should be performed by qualified technical personnel.

6.1 Recommended Maintenance Schedule

• Monthly:
  • Visually inspect the gate and motor for any signs of wear, damage, or loose connections.
  • Check the smooth movement of the gate, ensuring there are no obstructions or excessive friction.
  • Test all safety devices (photocells, safety edges) for proper functionality.
• Every 6 Months:
  • Lubricate moving parts of the gate (hinges, wheels, tracks) as recommended by the gate manufacturer.
  • Inspect electrical connections for corrosion or damage.
  • Verify the oil level in the gearmotor (if applicable and accessible by qualified personnel).
  • Check the integrity of the motor casing and mounting bolts.
• Annually:
  • Perform a comprehensive system check by a qualified technician.
  • Verify all safety parameters and adjust if necessary.
  • Replace any worn or damaged components with original FADINI spare parts.

6.2 Cleaning

Clean the exterior of the motor unit with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure no water enters the motor housing.

WARNING: Always disconnect power to the gate motor before performing any maintenance or cleaning to prevent accidental operation.

7. Troubleshooting

This section provides basic troubleshooting steps for common issues. For complex problems or if the issue persists, contact qualified technical support.

If the problem persists after attempting these solutions, please contact a qualified FADINI service technician.

8. Technical Specifications

9. Warranty and Support

9.1 Warranty Information

FADINI products are manufactured to high-quality standards and come with a manufacturer's warranty. The specific terms and duration of the warranty may vary based on your region and purchase date. Please retain your proof of purchase for warranty claims.

The warranty typically covers defects in materials and workmanship under normal use. It does not cover damage caused by improper installation, misuse, unauthorized modifications, or natural wear and tear.

9.2 Customer Support

For technical assistance, spare parts, or warranty service, please contact your authorized FADINI dealer or installer.

• Authorized Dealer: Refer to your purchase documentation for contact details of your authorized FADINI dealer.
• FADINI Official Website: Visit the official FADINI website for additional resources, product information, and contact options.

When contacting support, please have your product model (NYOTA 115 EVO) and purchase details readily available.

10. Compliance and Disposal

10.1 CE Declaration of Conformity

The FADINI NYOTA 115 EVO complies with the essential health and safety requirements of the relevant European Directives, including but not limited to:

• EN 13241: Industrial, commercial, and garage doors and gates - Product standard.
• EN 12453: Industrial, commercial, and garage doors and gates - Safety in use of power operated doors - Requirements.
• EN 12445: Industrial, commercial, and garage doors and gates - Safety in use of power operated doors - Test methods.

The manufacturer, MECCANICA FADINI, declares that this product is in conformity with the provisions of the applicable directives.

10.2 Disposal of Materials

At the end of its operational life, the product and its components must be disposed of responsibly and in accordance with local environmental regulations.

• Packaging Materials: Cardboard, plastic, and other packaging materials should be separated and recycled according to local guidelines.
• Electronic Components: The motor, control unit, and other electronic parts contain materials that must be disposed of at designated electronic waste collection points. Do not dispose of with general household waste.
• Oil: Any oil from the gearmotor must be collected and disposed of according to local regulations for hazardous waste.

Image 10.1: The FADINI NYOTA 115 EVO product packaging, securely strapped on a wooden pallet, ready for transport. This image illustrates the typical packaging for the product.