1. Introduction
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your Mr. Heater MH11BFLEX Buddy FLEX Portable Propane Heater. Please read all instructions carefully before use and retain this manual for future reference.
2. Important Safety Information
WARNING: Failure to follow these instructions can result in fire, explosion, carbon monoxide poisoning, or death.
- FOR OUTDOOR USE ONLY: This heater is designed for outdoor use. If used indoors, ensure adequate ventilation to prevent carbon monoxide accumulation.
- CARBON MONOXIDE HAZARD: This heater produces carbon monoxide, which is an odorless, colorless gas that can kill you. Use a carbon monoxide detector when operating indoors.
- FLAMMABLE MATERIALS: Keep the heater clear of all combustible materials, including gasoline and other flammable vapors and liquids. Maintain a minimum clearance of 30 inches from the top and sides, and 12 inches from the front.
- PROPANE GAS: Use only propane gas. Ensure all connections are tight and check for leaks with a soapy water solution before each use.
- OVERHEAT PROTECTION: The heater is equipped with an overheat protection system that will shut off the unit if it gets too hot.
- TIP-OVER SAFETY: The heater features a tip-over safety switch that automatically shuts off the unit if it is accidentally knocked over.
- Never leave the heater unattended while in operation.
- Do not use the heater in sleeping areas.
3. Package Contents
Verify that all items are present and undamaged:
- Mr. Heater MH11BFLEX Buddy FLEX Portable Propane Heater
- 10-Feet Propane Hose Assembly
- Instruction Manual (this document)
4. Setup
- Unpacking: Carefully remove the heater and all accessories from the packaging. Inspect for any shipping damage.
- Placement: Place the heater on a firm, level surface. Ensure adequate clearance from combustible materials as specified in the safety section. For indoor use, ensure proper ventilation.
- Connecting the Propane Hose:

Image: The Mr. Heater MH11BFLEX Buddy FLEX Portable Propane Heater shown connected to a larger propane tank via a green hose. The heater features a red and black casing with a protective metal grill over the heating elements.

Image: A close-up view of the 10-foot green propane hose assembly. One end has a black plastic hand-tighten fitting for connecting to the heater, and the other end has a brass fitting for a standard propane tank.
- Connect the appropriate end of the 10-foot propane hose assembly to the heater's propane inlet.
- Connect the other end of the hose to your propane cylinder.
- Tighten all connections securely by hand. Do not overtighten.
- Leak Test: Apply a soapy water solution to all connections. Open the propane cylinder valve. If bubbles appear, there is a leak. Close the valve immediately and re-tighten connections. Repeat the leak test until no bubbles are present.
5. Operating Instructions

Image: A detailed view of the red control knob on the Mr. Heater Buddy FLEX. Markings around the knob indicate 'OFF', 'PILOT', 'LO', and 'HI' settings for operation.
- Open Propane Valve: Slowly open the valve on your propane cylinder.
- Ignition:
- Push and hold the control knob down.
- Rotate the knob to the 'PILOT' position.
- Continue to hold the knob down for 30-60 seconds after the pilot flame ignites to allow the thermocouple to heat up.
- Release the knob. If the pilot light extinguishes, repeat the process.
- Adjusting Heat: Once the pilot is lit, push and rotate the control knob to your desired heat setting: 'LO' (Low), 'MED' (Medium), or 'HI' (High). The ceramic heating elements will begin to glow.

Image: A close-up of the Mr. Heater Buddy FLEX's ceramic heating element, visibly glowing red, indicating active heat production.
- Fan Operation: The Buddy FLEX model may include an integrated fan to help circulate heat. If present, activate the fan according to the controls on your specific unit.
- Shutting Down: To turn off the heater, rotate the control knob to the 'OFF' position. Close the valve on the propane cylinder.
6. Maintenance
- Cleaning: Ensure the heater is completely cool before cleaning. Use a soft, damp cloth to wipe down exterior surfaces. Do not use abrasive cleaners or solvents.
- Burner Inspection: Periodically inspect the ceramic burner surface for any debris or blockages. Gently remove any obstructions with a soft brush.
- Hose and Connections: Regularly check the propane hose for signs of wear, cuts, or damage. Perform a leak test before each use. Replace damaged hoses immediately.
- Storage: When not in use, disconnect the propane cylinder and store the heater in a cool, dry place away from direct sunlight and heat sources.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater will not light or pilot light will not stay lit. | No propane flow, low propane pressure, air in line, faulty thermocouple, high altitude. | Check propane cylinder for fuel. Ensure cylinder valve is fully open. Bleed air from line by attempting ignition several times. Hold pilot knob longer. Consult manufacturer for high altitude operation guidelines. |
| Reduced heat output. | Low propane level, partially closed propane valve, dirty burner. | Check propane level. Ensure propane valve is fully open. Clean burner surface as per maintenance instructions. |
| Heater shuts off unexpectedly. | Tip-over switch activated, low oxygen sensor activated, overheat protection activated. | Ensure heater is on a stable surface. Provide adequate ventilation. Allow heater to cool down before restarting. |
8. Specifications
- Brand: Mr. Heater
- Model: MH11BFLEX
- Heat Output: 11,000 British Thermal Units (BTU)
- Fuel Type: Propane
- Burner Type: Radiant
- Heating Coverage: 100-150 square feet
- Indoor/Outdoor Usage: Indoor, Outdoor (with proper ventilation)
- Special Features: Overheat Protection, Portable, Tip-Over Safety
- Form Factor: Pedestal
- Mounting Type: Floor Mount
- Product Dimensions: 19.8 x 15.9 x 16.2 inches
- Power Source: Gas Powered
- UPC: 782314910045
9. Warranty and Support
For warranty information, technical support, or replacement parts, please refer to the official Mr. Heater website or contact their customer service department. Keep your purchase receipt and product model number (MH11BFLEX) handy when contacting support.