Olympic Electric Infinity Water Heater - Digital 60 Liter User Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Olympic Electric Infinity Digital 60 Liter Water Heater. Please read these instructions thoroughly before installation and retain this manual for future reference. Proper installation and adherence to these guidelines will ensure optimal performance and longevity of your appliance.

2. Safety Information

Important Safety Instructions:

• Read all instructions before using this water heater.
• This appliance must be installed by a qualified technician in accordance with all local codes and regulations.
• Ensure the electrical supply matches the voltage specified on the water heater's rating label (220 Volts, 50/60 Hz).
• Do not operate the water heater if it is damaged or malfunctioning. Disconnect power immediately.
• Never block the pressure relief valve. Regular inspection of this valve is crucial for safety.
• Do not store or use flammable materials near the water heater.
• Always drain the water heater before performing any maintenance or if it will be exposed to freezing temperatures.
• Children should be supervised to ensure they do not play with the appliance.

3. Package Contents

Verify that all components are present and undamaged upon unpacking:

• Olympic Electric Infinity Digital Water Heater unit (60 Liter)
• Pressure Relief Valve
• Mounting Bracket(s)
• Fasteners (screws, anchors)
• User Manual (this document)

Note: Additional plumbing fittings or electrical wiring may be required for installation and are typically not included.

4. Setup and Installation

Installation must be performed by a certified professional.

4.1 Pre-Installation Checks

• Location: Choose a location that is protected from freezing temperatures, close to the main water supply and electrical outlet, and capable of supporting the full weight of the water heater when filled (approximately 87.2 kg for 60 liters).
• Water Supply: Ensure adequate water pressure (maximum 8 Bars).
• Electrical Supply: Verify that the electrical circuit can handle 1200 watts at 220 volts. A dedicated circuit is recommended.

4.2 Mounting the Water Heater

1. Mark the desired mounting points on a sturdy wall, ensuring the heater is level.
2. Drill holes and insert appropriate wall anchors.
3. Securely attach the mounting bracket(s) to the wall.
4. Carefully lift and hang the water heater onto the bracket(s). Ensure it is firmly seated.

4.3 Plumbing Connections

1. Install the pressure relief valve into the designated opening on the water heater. Ensure proper sealing.
2. Connect the cold water inlet pipe to the marked inlet on the water heater (usually blue or marked 'C').
3. Connect the hot water outlet pipe to the marked outlet on the water heater (usually red or marked 'H').
4. Ensure all connections are tight and leak-free.

4.4 Electrical Connections

1. Ensure the main power supply is OFF before making any electrical connections.
2. Connect the water heater's electrical wiring to a properly grounded 220V, 50/60Hz power source. Follow local electrical codes.
3. Verify all connections are secure and insulated.

4.5 Initial Filling

1. Before turning on the power, open a hot water faucet in your home to allow air to escape from the tank.
2. Slowly open the cold water supply valve to the water heater.
3. Allow the tank to fill completely until water flows steadily from the open hot water faucet.
4. Close the hot water faucet.

Figure 1: Front view of the Olympic Electric Infinity Digital 60 Liter Water Heater. It is white with a dark grey base. A digital display showing '68' is visible on the lower front, indicating the water temperature. The 'OLYMPIC ELECTRIC' logo is located on the upper front.

5. Operating Instructions

5.1 Powering On/Off

• After ensuring the tank is full of water, turn on the main electrical power supply to the water heater.
• The digital display on the front of the unit will illuminate, showing the current water temperature.
• To turn off the heater, switch off the main electrical power supply.

5.2 Temperature Adjustment

The Olympic Infinity water heater features a digital display for precise temperature control.

• Use the control buttons located near the digital display to increase or decrease the desired water temperature.
• The display will show the set temperature, then revert to showing the actual water temperature as it heats.
• The heater will automatically maintain the set temperature.

5.3 Economical Power Consumption

This model is designed for economical power consumption. To maximize energy efficiency:

• Set the temperature to the lowest comfortable level.
• Consider using a timer (if available or installed separately) to heat water only when needed.
• Ensure proper insulation of hot water pipes.

6. Maintenance

Regular maintenance ensures the longevity and efficient operation of your water heater.

6.1 Draining the Tank

Draining the tank annually can help remove sediment buildup.

1. Turn off the electrical power supply to the water heater.
2. Close the cold water supply valve to the water heater.
3. Open a hot water faucet in your home to relieve pressure.
4. Connect a hose to the drain valve at the bottom of the water heater and direct it to a suitable drain.
5. Open the drain valve and allow the tank to empty.
6. Once drained, close the drain valve, remove the hose, and refill the tank as described in Section 4.5 before restoring power.

6.2 Pressure Relief Valve Inspection

Test the pressure relief valve at least once a year to ensure it is not obstructed. Follow the manufacturer's instructions for the valve. Caution: Hot water will be discharged.

6.3 Anode Rod Inspection/Replacement

The anode rod protects the tank from corrosion. It should be inspected every 1-3 years and replaced if significantly depleted. This procedure should be performed by a qualified technician.

7. Troubleshooting

Before contacting service, review these common issues:

If troubleshooting steps do not resolve the issue, or if you suspect a serious malfunction, disconnect power and contact a qualified service technician.

8. Specifications

9. Warranty and Support

Your Olympic Electric Infinity Water Heater is covered by a manufacturer's warranty. To activate and validate your warranty, it is often required that the product be installed by an authorized service technician from Olympic. Please refer to the warranty card included with your product or contact Olympic customer service for specific terms, conditions, and activation procedures.

For technical support, service requests, or warranty claims, please contact Olympic customer service directly. Ensure you have your product model number (Infinity) and proof of purchase available when contacting support.

Note: Unauthorized installation or repairs may void your warranty.