LEDONE LOD-036360090 36W IP65 LED Driver Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your LEDONE LOD-036360090 36W IP65 LED Driver. This constant current power supply is designed for various LED lighting applications, offering reliable performance in both outdoor and indoor environments. Please read this manual thoroughly before installation and retain it for future reference.

2. Safety Information

• Electrical Hazard: Installation should only be performed by a qualified electrician or trained personnel. Ensure power is disconnected at the circuit breaker before any installation or maintenance.
• Proper Grounding: Always ensure the LED driver is properly grounded according to local electrical codes.
• Voltage Compatibility: Verify that the input voltage (100-277Vac) and output voltage/current (24-36Vdc, 900mA) of the driver match the requirements of your LED lighting fixture. Incorrect voltage can damage the driver or the LED lights.
• Wiring: Use appropriate gauge wiring for connections. Ensure all connections are secure and insulated to prevent short circuits.
• Operating Environment: Do not exceed the specified operating temperature range (-20°C to 55°C / -4°F to 131°F). Ensure adequate ventilation around the driver.
• Waterproof Rating: The IP65 rating indicates protection against dust and low-pressure water jets. While suitable for damp locations, avoid submerging the unit.
• Non-Dimmable: This driver is non-dimmable. If dimming functionality is required, it is only compatible with RGB dimmers.

3. Product Features

• IP65 Waterproof: Features a die-cast aluminum housing with IP65 super waterproof rating, making it suitable for damp or harsh outdoor and indoor locations.
• Wide Application: Ideal for LED strip lights, LED type C tubes, surveillance cameras, outdoor lights, and other compatible LED products.
• Constant Current Output: Provides a stable 900mA constant current output for consistent LED performance.
• Broad Input Voltage: Operates efficiently with an input voltage range of 100-277Vac, 50/60Hz.
• Stable Performance: Designed for long lifespan with CE certificates, no noise operation, isolation protection, and safety features.
• Pre-wired Cords: Equipped with 6-inch cords on each side for convenient installation.

Image: The LEDONE 36W LED Driver highlighting its IP65 waterproof rating, suitable for various environments.

4. Specifications

Image: Close-up of the LEDONE 36W LED Driver label showing electrical specifications and product size details.

Image: The LEDONE 36W LED Driver with its physical dimensions clearly marked for reference.

5. Installation and Setup

Important: Ensure all power is OFF before proceeding with installation.

1. Mounting: Securely mount the LED driver in a suitable location, ensuring it is protected from physical damage and has adequate ventilation. The IP65 rating allows for use in damp locations, but direct exposure to high-pressure water or submersion should be avoided.
2. Input Wiring (AC): Connect the AC input wires from your power source to the driver's input terminals. The driver has two input wires, typically brown (AC-L) and blue (AC-N). Refer to the product label for specific wiring identification. Ensure connections are tight and insulated.
3. Output Wiring (DC): Connect the DC output wires from the driver to your LED lighting fixture. The driver has two output wires, typically red (V+) and black (V-). Ensure correct polarity (+ to + and - to -) to prevent damage to the LED lights.
4. Grounding: If your installation requires grounding, ensure the driver's metal casing (if applicable) or the system's ground wire is properly connected to an earth ground.
5. Power On: Once all connections are secure and verified, restore power to the circuit. The LED lights should illuminate.

Image: The LEDONE 36W LED Driver integrated into diverse lighting setups, demonstrating its versatility for different applications.

6. Operation

The LEDONE LOD-036360090 is a constant current LED driver. Once properly installed and powered, it will provide a stable 900mA current to your connected LED lights within the specified voltage range (24-36Vdc).

• Non-Dimmable: This driver is designed for non-dimmable applications. It will provide full output when powered.
• RGB Dimmer Compatibility: If dimming is desired, this driver is only compatible with specific RGB dimmers that control the LED fixture itself, not by modulating the driver's input or output directly. Consult your RGB dimmer's instructions for compatibility.

Image: The LEDONE 36W LED Driver powering a variety of decorative and functional LED lights, showcasing its application range.

7. Maintenance

The LEDONE LOD-036360090 LED driver is designed for minimal maintenance. However, periodic checks can help ensure its longevity and optimal performance:

• Visual Inspection: Periodically inspect the driver and its wiring for any signs of damage, wear, or loose connections.
• Cleaning: If installed in a dusty environment, gently clean the exterior of the driver with a dry cloth to prevent heat buildup. Ensure power is off before cleaning.
• Environmental Check: Ensure the operating environment remains within the specified temperature and humidity ranges.

8. Troubleshooting

If you encounter issues with your LEDONE LED driver, refer to the following common troubleshooting steps:

• No Light Output:
  • Check if the power supply to the driver is active.
  • Verify all input and output wiring connections are secure and correct (polarity).
  • Ensure the LED fixture itself is functional and compatible with the driver's output specifications.
  • Check for any tripped circuit breakers or blown fuses.
• Flickering Lights:
  • Inspect for loose wiring connections on both input and output sides.
  • Ensure the LED fixture is not drawing more current than the driver's capacity.
  • Verify stable input voltage.
• Driver Overheating:
  • Ensure adequate ventilation around the driver. Do not enclose it in a sealed space without proper airflow.
  • Verify the ambient temperature is within the specified operating range.
  • Confirm the load (LED lights) does not exceed the driver's maximum wattage.

If these steps do not resolve the issue, please contact LEDONE customer support for further assistance.

9. Warranty and Support

LEDONE is committed to providing quality lighting solutions and customer satisfaction. For any questions, technical support, or warranty inquiries regarding your LOD-036360090 LED driver, please contact LEDONE customer service. Our team is based in California and dedicated to offering reliable service.

Please have your product model number (LOD-036360090) and purchase information ready when contacting support.