Introduction
Thank you for choosing the WILLED Dimmable Touch Lights. These portable LED puck lights are designed for versatile use in various indoor environments such as cabinets, wardrobes, counters, kitchens, and bedrooms. Featuring dimmable brightness, a rechargeable battery, and magnetic installation, they offer convenient and efficient lighting. Please read this manual carefully to ensure proper use and maintenance of your product.
What's in the Box
Upon opening your package, please verify that all the following components are included:
- 2 x LED Night Lights
- 2 x Iron Sheets with 3M Adhesive Tape
- 2 x Micro USB Charging Cables
- 1 x User Manual
Image: Package contents including two LED puck lights, two micro USB cables, and two adhesive metal sheets.
Setup and Installation
The WILLED Dimmable Touch Lights are designed for easy, wireless installation. They can be attached to metal surfaces directly using their built-in magnets or to non-metal surfaces using the provided adhesive iron sheets.
- Prepare the Surface: Ensure the desired installation surface is clean, dry, and smooth for optimal adhesion.
- Attach Adhesive Iron Sheet (for non-metal surfaces):
- Peel off the protective film from one side of the 3M adhesive tape on the iron sheet.
- Firmly press the adhesive side of the iron sheet onto the chosen non-metal surface. Hold for a few seconds to ensure strong adhesion.
- Mount the Light: The LED puck light has a built-in magnet. Simply attach the light to the installed iron sheet or directly to any suitable metal surface. The magnetic connection allows for easy removal for charging or relocation.
Image: Step-by-step guide for magnetic installation with adhesive metal plates.
Note: For best results, allow the adhesive to set for a few hours before attaching the light, especially if the light will be frequently removed.
Operating Instructions
The WILLED Dimmable Touch Lights feature intuitive touch controls for power and brightness adjustment.
- Power ON/OFF: Lightly touch the power icon on the surface of the light for a short duration to turn the light ON or OFF.
- Adjust Brightness (Dimming): When the light is ON, press and hold the power icon. The brightness will gradually increase or decrease. Release your finger when the desired brightness level is reached. The light will remember your last brightness setting for future use.
Image: Examples of light usage in different home settings.
Charging
Your WILLED Dimmable Touch Light is equipped with a built-in 1000mAh rechargeable battery. It is recommended to fully charge the light before its first use.
- Charging Port: Locate the micro USB charging port on the side of the light.
- Connect Charger: Use the provided micro USB cable to connect the light to a 5V USB power source (e.g., computer, USB wall adapter, power bank).
- Charging Indicator: A red indicator light will illuminate during charging. The indicator light will turn off or change color (depending on the model) once charging is complete.
- Battery Life: A full charge provides approximately 6 hours of illumination at the brightest setting and up to 120 hours at the darkest setting.
Image: Light being charged via USB, showing the 1000mAh battery capacity.
Maintenance
To ensure the longevity and optimal performance of your WILLED Dimmable Touch Lights, follow these simple maintenance guidelines:
- Cleaning: Wipe the surface of the light with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish.
- Water Exposure: These lights are designed for indoor use only and are not waterproof. Avoid exposure to water or high humidity.
- Battery Care: To preserve battery life, avoid fully discharging the battery frequently. Recharge the light when brightness noticeably diminishes. If storing for an extended period, charge the light every 3-6 months.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn ON. | Battery is depleted. | Charge the light using the provided USB cable. Ensure the charging indicator illuminates. |
| Light is dim or flickers. | Low battery or incorrect brightness setting. | Recharge the light. If already charged, press and hold the touch button to increase brightness. |
| Light falls off the surface. | Adhesive not strong enough or surface not clean. | Ensure the surface is clean and dry before applying the adhesive iron sheet. Replace the 3M adhesive tape if necessary. |
| Light turns off unexpectedly. | Battery depleted or potential undocumented timer (as noted by some users). | Recharge the light. If the issue persists after charging, contact customer support. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | WNL-A2 |
| Light Type | LED |
| Number of LEDs | 6 |
| Brightness | Dimmable (Max. 60 lumens) |
| Color Temperature | 3000K (Warm White) |
| Battery Capacity | 1000mAh (Rechargeable) |
| Input Voltage | 5V (USB) |
| Control Method | Touch |
| Mounting Type | Magnetic / Adhesive |
| Material | Acrylonitrile Butadiene Styrene (ABS), Iron |
| Product Dimensions | 1.7D x 8.5W x 8.5H centimetres |
| Item Weight | 172 g |
| Indoor/Outdoor Use | Indoor Use Only |
| Water Resistance | Not Water Resistant |
Warranty and Support
WILLED provides a 12-month warranty for this product. If you encounter any issues or have questions regarding your WILLED Dimmable Touch Lights, please do not hesitate to contact our customer support team. We are committed to providing professional assistance and ensuring your satisfaction.
Please refer to your purchase documentation or the WILLED official website for contact information.