Product Overview
The LS2 Assault Helmet is engineered for motorcycle riders, featuring a lightweight and strong Kinetic Polymer Alloy (KPA) shell combined with a multi-density EPS liner. It is designed across three shell sizes to ensure optimal fit and protection. The helmet incorporates advanced ventilation and a comfortable, removable interior for extended wear.
Image: Front-side view of the LS2 Assault Full Face Motorcycle Helmet in matte black.
Key Features
- DOT approved, meeting FMVSS 218 Standard for safety.
- Kinetic Polymer Alloy (KPA) shell construction for durability and light weight.
- Pinlock-ready, 3D optically correct shield with a Quick Release System for clear vision and easy changes.
- Integrated inner drop-down sun shield for adaptable vision in varying light conditions.
- Fully removable and washable comfort liner for hygiene and long-term comfort.
Setup and Initial Use
Before your first ride, ensure the helmet is properly fitted and all components are securely in place. Proper fit is crucial for both comfort and safety.
1. Sizing and Fit
Refer to the sizing guide to ensure you have the correct helmet size. The helmet should fit snugly around your head without causing pressure points. The cheek pads should make firm contact with your cheeks. If the helmet moves freely when you shake your head, it is too large.
Image: Interior view of the LS2 Assault Helmet, highlighting the removable comfort liner.
2. Visor Preparation
Remove any protective films from both the outer clear faceshield and the inner drop-down sun shield before use. Ensure the faceshield is securely attached to the helmet's quick release system.
3. Chin Strap Adjustment
Fasten the chin strap securely. The strap should be tight enough so that you cannot pull the helmet off your head when pulling upwards from the rear, but not so tight as to cause discomfort or restrict breathing. Ensure the D-ring or quick-release buckle is properly engaged.
Operation
Understanding the helmet's features will enhance your riding experience and safety.
1. Faceshield Operation
The clear faceshield can be opened and closed using the tab located at the bottom center. It features multiple detent positions to allow for varying levels of airflow. To remove the faceshield for cleaning or replacement, utilize the Quick Release System mechanisms on either side of the helmet.
Image: Side view of the LS2 Assault Helmet with the clear faceshield in an open position.
2. Inner Drop-Down Sun Shield
The integrated sun shield is operated by a slider mechanism, typically located on the left side of the helmet near the pivot point of the main faceshield. Slide it down for sun protection and up when not needed. This shield is designed for daytime use and should not be used in low light conditions or at night.
Image: Front view of the LS2 Assault Helmet with the inner sun shield deployed.
3. Ventilation System
The helmet features adjustable vents on the chin bar and at the top of the helmet. These can be opened or closed to control airflow. The rear spoiler and side venturi vents work to exhaust hot air, providing dynamic flow-through ventilation. Adjust these vents according to weather conditions and personal comfort.
Maintenance
Regular maintenance will prolong the life and effectiveness of your helmet.
1. Shell Cleaning
Clean the helmet shell with a soft, damp cloth and mild soap. Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage the KPA material and paint finish. Rinse thoroughly and dry with a soft, clean cloth.
Image: Rear view of the LS2 Assault Helmet, showing the exhaust vents.
2. Visor and Sun Shield Cleaning
Clean the faceshield and sun shield with warm water and a soft cloth. For stubborn dirt or insects, soak a soft cloth in warm water and lay it over the shield for a few minutes to loosen debris before gently wiping clean. Do not use abrasive materials or chemical cleaners that can scratch or damage the optical coatings.
3. Removable Liner Care
The interior comfort liner is fully removable and washable. Gently detach the liner components from the helmet. Hand wash with mild soap and cool water, or machine wash on a gentle cycle in a laundry bag. Air dry completely before reinstalling into the helmet. Ensure no moisture remains to prevent mildew.
4. Storage
Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from dust and scratches when not in use.
Troubleshooting
Common issues and their potential solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Visor fogging | Lack of airflow, temperature difference, high humidity | Open vents, slightly crack the visor, consider installing a Pinlock lens insert (sold separately). |
| Helmet feels too tight/loose | Incorrect size, liner not settled | Verify size using the sizing guide. Allow new liner to break in. If still uncomfortable, consider a different size. |
| Excessive wind noise | Improper fit, open vents, worn neck roll | Ensure proper fit and chin strap tension. Close unused vents. Check for wear on the neck roll seal. |
| Sun shield not retracting fully | Debris in mechanism, misalignment | Inspect the slider mechanism for obstructions. Gently clean the area. Do not force the mechanism. |
Specifications
| Feature | Detail |
|---|---|
| Item Weight | 5.5 Pounds |
| Item Model Number | 800-1194 |
| Department | unisex-adult |
| Date First Available | March 11, 2020 |
| Manufacturer | LS2 Helmets |
| ASIN | B09184YDNC |
| Fabric Type | 50% Nylon, 50% Spandex (Liner) |
| Origin | Made in the USA |
Safety Information
This LS2 Assault Helmet complies with US Federal Motor Vehicle Safety Standard 218 (FMVSS 218) (DOT FMVSS No. 218 Certified). Always wear a helmet that meets safety standards and ensure it is properly fitted and fastened before every ride. Never modify your helmet, as this can compromise its protective capabilities.
Sizing Guide
Use the following table to determine the appropriate helmet size based on your head circumference.
US Motorcycle Helmet
| Brand Size | Head Circumference (in) |
|---|---|
| 2XS | 20 - 20.5 |
| XS | 20.9 - 21.3 |
| S | 21.6 - 22 |
| M | 22.5 - 22.9 |
| L | 23.3 - 23.6 |
| XL | 24 - 24.4 |
| 2XL | 24.8 - 25.3 |
| 3XL | 25.6 - 26 |
Warranty Information
For detailed warranty information regarding your LS2 Assault Helmet, please refer to the official LS2 Helmets website or contact their customer support directly. Warranty terms typically cover manufacturing defects and materials for a specified period from the date of purchase.
Support
If you require further assistance, have questions not covered in this manual, or need to report an issue, please contact LS2 Helmets customer support. You can often find contact information and additional resources on the official LS2 website: Visit the LS2 Store on Amazon.
