1. Product Overview
The Empava 71-inch Whirlpool Bathtub is designed for two persons, featuring 16 strategically placed water jets for a hydro-massage experience. Constructed from glossy white acrylic reinforced with fiberglass and supported by a stainless-steel frame, this tub is built for durability and insulation. It includes pre-installed accessories such as a waterfall faucet, knobs, a 45-inch showerhead, and pillows, providing a complete and comfortable spa experience in your home.
Image: Top-down view of the Empava 2-person whirlpool bathtub, highlighting the arrangement of the 16 water jets and two integrated headrests.
2. Important Safety Instructions
To reduce the risk of injury, electric shock, fire, or damage to the product, please adhere to the following safety guidelines:
- Always ensure the bathtub is properly grounded according to local electrical codes.
- Do not operate the whirlpool system without sufficient water in the tub to cover the jets.
- Maintain water temperature below 104°F (40°C) to prevent hyperthermia.
- Children should be supervised at all times when in or near the bathtub.
- Do not use abrasive cleaners or harsh chemicals that could damage the acrylic surface or internal components.
- The motor is UL Certified and comes with a pre-installed US standard 120V GFCI Power Cord. Do not modify or bypass this safety device.
- Avoid placing electrical appliances near the bathtub.
3. Components
Your Empava Whirlpool Bathtub package includes the following main components and accessories:
- Acrylic Whirlpool Bathtub Unit with integrated jets and motor
- Stainless-steel support frame
- 45" length showerhead
- Chrome polished drain
- Control knobs
- Pillows (headrests)
- Waterfall faucet
- Pre-installed 120V GFCI Power Cord
Image: Front view of the Empava 2-person whirlpool bathtub, showcasing its design and the integrated headrests.
4. Setup and Installation
4.1 Pre-Installation Checklist
- Verify product dimensions (70.8"L x 47.25"W x 26.7"H) against your bathroom space.
- Ensure the floor can support the weight of the tub filled with water (approx. 177 gallons + 180 lbs tub weight + user weight).
- Confirm availability of a 110V electrical outlet with proper grounding and GFCI protection.
- Ensure access to hot and cold water supply lines and a suitable drain connection.
4.2 Placement
Position the bathtub on a level, stable surface. Ensure adequate clearance around the tub for maintenance and access. The 3-side apron design is suitable for alcove installations.
4.3 Electrical Connection
The bathtub comes with a pre-installed 120V GFCI power cord. Connect this cord to a dedicated, properly grounded 110V electrical outlet. Do not use extension cords or adapters. Consult a qualified electrician if you are unsure about your electrical setup.
4.4 Plumbing Connection
Connect the hot and cold water supply lines to the designated inlets on the bathtub. Ensure all connections are secure and leak-free. Connect the bathtub drain to your household drainage system. The right-side drain configuration should align with your plumbing setup.
Image: Detailed dimension diagram, crucial for planning installation space and plumbing connections.
Image: Underside view of the bathtub, illustrating the robust stainless-steel frame and the pre-installed plumbing and electrical components.
5. Operating Instructions
5.1 Filling the Bathtub
Ensure the drain cover is closed. Use the waterfall faucet to fill the bathtub with water to the desired level. Ensure the water level is above the highest jets before activating the whirlpool system.
5.2 Activating Whirlpool Jets
Once the tub is filled, locate the pneumatic switch (air button) on the tub deck. Press this button to activate the 1.5 HP motor and engage the whirlpool jets. Press again to turn off the system.
5.3 Adjusting Jets
Some jets may allow for direction and flow adjustment. Rotate the outer ring of individual jets to change the direction of the water flow. For flow adjustment, refer to the specific jet design; some may allow for partial closure to increase pressure on other jets.
5.4 Draining the Bathtub
To drain the tub, rotate the chrome polished drain cover to the open position. The water will flow out through the right-side drain.
Image: Close-up of the ergonomic control knobs and the 45-inch showerhead, demonstrating ease of use.
6. Maintenance
6.1 Cleaning the Bathtub
For daily cleaning, wipe the acrylic surface with a soft cloth and a mild, non-abrasive bathroom cleaner. Rinse thoroughly with water. Avoid using harsh chemicals, abrasive pads, or solvents, as these can damage the glossy finish.
6.2 Cleaning the Jet System
Periodically, fill the tub with warm water above the jets and add a small amount of a non-foaming, non-abrasive jet cleaner or a few tablespoons of white vinegar. Run the whirlpool system for 10-15 minutes. Drain the tub and refill with clean water, running the jets again for a few minutes to rinse the system. This helps prevent buildup and maintain jet performance.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Whirlpool jets not working | No power; GFCI tripped; Insufficient water level; Motor issue. | Check power connection; Reset GFCI; Ensure water level is above jets; Contact customer support if motor is unresponsive. |
| Weak jet pressure | Air intake blocked; Clogged jets; Low water level. | Clear any obstructions from air intake; Clean jets as per maintenance section; Ensure adequate water level. |
| Water leaking from connections | Loose plumbing connections; Damaged seals. | Tighten connections carefully; Inspect seals for damage and replace if necessary. |
| Unusual noise from motor | Debris in pump; Motor malfunction. | Turn off power and inspect for debris (if accessible); Contact customer support for motor issues. |
8. Technical Specifications
| Feature | Specification |
|---|---|
| Model Number | 71" Acrylic Alcove Whirlpool Bathtub |
| Dimensions (L x W x H) | 70.8" x 47.25" x 26.7" |
| Interior Dimension (L x W x H) | 45" x 33" x 18" |
| Water Depth to Overflow | 15.75" (15¾") |
| Material | Acrylic, Fiberglass, Stainless Steel |
| Color | White |
| Capacity | 177 Gallons |
| Item Weight | 180 Pounds |
| Voltage | 110 Volts |
| Motor Horsepower | 1.5 HP |
| Number of Jets | 16 |
| Installation Type | Alcove |
| Drain Location | Right |
| Certifications | UL Certified Motor |
9. Warranty and Customer Support
9.1 Warranty Information
The Empava 2 Person Whirlpool Bathtub comes with a 3-year limited manufacturer warranty. Please retain your proof of purchase for warranty claims. This warranty covers defects in materials and workmanship under normal use and service.
9.2 Customer Support
For technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact Empava customer support. You can find contact information on the official Empava website or through your retailer.
