1. Introduction
The EverBrite Motion Sensor Night Lights provide automatic, soft warm illumination for various indoor spaces. Designed for convenience and energy efficiency, these battery-powered LED lights enhance safety and comfort in dark areas such as hallways, stairs, bedrooms, and closets. The integrated motion sensor activates the light only when movement is detected in low-light conditions, conserving battery life.
Image 1.1: EverBrite Motion Sensor Night Lights (3-Pack).
2. Package Contents
Verify that all items are present in the package:
- 3 x Motion Sensor Lights
- 9 x AA Alkaline Batteries (3 per light)
- 6 x Screws
- 6 x Anchors
- 3 x Double-sided Tapes
- 1 x User Manual (this document)
Image 2.1: Package contents for the EverBrite Motion Sensor Night Lights.
3. Setup and Installation
3.1 Battery Installation
- Locate the mounting plate on the back of the night light.
- Slide the mounting plate downwards to remove it from the main unit.
- Insert 3 AA batteries into the battery compartment, ensuring correct polarity (+/-).
- Slide the mounting plate back onto the main unit until it clicks securely.
Image 3.1: Battery installation steps.
3.2 Mounting Options
The EverBrite Motion Sensor Night Lights offer two installation methods:
Option 1: Mounting with Double-Sided Tape
- Clean the desired mounting surface to ensure it is dry and free of dust or grease.
- Peel the protective backing from one side of the double-sided tape.
- Apply the tape firmly to the back of the night light's mounting plate.
- Peel the remaining protective backing from the tape.
- Press the night light firmly onto the desired surface for at least 30 seconds.
Note: For optimal adhesion, ensure the surface is smooth and clean. The adhesive may be less effective on textured or uneven surfaces.
Option 2: Mounting with Screws
- Determine the desired mounting location.
- Using the mounting plate as a template, mark the positions for two drill holes.
- Drill two holes at the marked positions. For drywall, insert the provided anchors into the holes.
- Align the mounting plate with the drilled holes and fasten it to the wall using the provided screws.
- Slide the main night light unit onto the secured mounting plate until it locks into place.
Image 3.2: Two methods of installation: tape and screws.
4. Operating Instructions
4.1 Motion Sensor Functionality
The EverBrite Motion Sensor Night Light is equipped with a passive infrared (PIR) motion sensor and a light sensor. It operates in the following manner:
- Automatic Activation: The light will only turn on when motion is detected AND the ambient light conditions are dark enough (approximately 0-20 lux). This prevents the light from activating unnecessarily during daylight hours, conserving battery life.
- Motion Detection Range: The sensor can detect motion from up to 15 feet (5 meters) away, with a perceptual angle of 150 degrees.
- Automatic Deactivation: After motion is no longer detected, the light will automatically turn off after a preset duration of either 30 or 45 seconds.
Image 4.1: Motion sensor range and angle.
Image 4.2: Automatic lighting logic.
4.2 Setting the Auto-Off Timer
Each night light features a switch to select the auto-off duration:
- Locate the small slide switch on the side or back of the night light unit.
- Slide the switch to select either "30s" for a 30-second auto-off delay or "45s" for a 45-second auto-off delay after motion ceases.
Image 4.3: Auto-off timer selection switch.
5. Maintenance
5.1 Battery Replacement
When the light output diminishes or the light fails to activate, it is time to replace the batteries. Follow the steps outlined in Section 3.1 "Battery Installation" to replace the 3 AA batteries in each unit.
Recommendation: Use high-quality alkaline batteries for optimal performance and longevity.
5.2 Cleaning
To clean the night light, gently wipe the surface with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, as these can damage the unit or its electronic components.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light stays on continuously or turns off too slowly. |
|
|
| Light falls off the wall (tape mounting). |
|
|
7. Specifications
| Feature | Detail |
|---|---|
| Brand | EverBrite |
| Model (ASIN) | B08Y8QCZ6M |
| Light Source Type | LED |
| Light Color | Soft Warm Light |
| Power Source | Battery Powered (3 x AA batteries per unit) |
| Special Features | Motion Sensor, Energy Efficient |
| Motion Sensor Range | Up to 15 ft (5m), 150° perceptual angle |
| Auto-Off Timer | 30 or 45 seconds (adjustable) |
| Activation Condition | Only in dark surroundings (0-20 lux) |
| Product Dimensions (each) | 4" W x 3" H x 1-1/6" D (1.14"D x 4"W x 3"H) |
| Material | Acrylonitrile Butadiene Styrene (ABS Plastic) |
| Finish Type | Polished |
| Indoor/Outdoor Usage | Indoor |
| Water Resistance Level | Not Water Resistant |
| Wattage | 1.35 watts |
8. Warranty and Support
8.1 Warranty Information
No specific warranty information is provided in this manual. For details regarding product warranty, please refer to the product packaging or contact EverBrite customer support directly.
8.2 Customer Support
For further assistance, technical support, or inquiries about your EverBrite Motion Sensor Night Lights, please visit the official EverBrite website or contact their customer service department through the retailer where the product was purchased.
You can also visit the EverBrite Store on Amazon: EverBrite Store