1. Introduction
Thank you for choosing the Veken Smart Bidet Toilet Seat. This manual provides essential information for the safe installation, operation, and maintenance of your new bidet seat. Please read this manual thoroughly before installation and keep it for future reference.
2. Safety Information
To ensure safe operation and prevent injury or damage, please observe the following safety precautions:
- Electrical Safety: This appliance must be connected to a Ground Fault Circuit Interrupter (GFCI) outlet. Do not use extension cords unless they are specifically rated for bathroom use and GFCI protected. Ensure the power cord is not pinched or damaged.
- Water Safety: Turn off the main water supply before installation or maintenance. Ensure all water connections are secure to prevent leaks. Do not expose the bidet seat to excessive moisture or spray water directly onto the unit.
- Installation: Only install the bidet seat on an elongated toilet bowl. Ensure the toilet bowl is stable and properly secured to the floor.
- Cleaning: Disconnect power before cleaning. Use mild, non-abrasive cleaners.
- Children and Individuals with Reduced Capabilities: This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
3. Package Contents
Verify that all components are present before beginning installation:
- Veken Smart Bidet Toilet Seat (VK813)
- Water Supply Hose
- T-Adapter for water connection
- Mounting Plate
- Mounting Screws and Rubber Grommets
- Plastic Wing Nuts
- Installation Template
4. Product Features
The Veken Smart Bidet Toilet Seat VK813 offers a range of features designed for enhanced hygiene and comfort:
- Heated Seat: Provides adjustable warmth for comfort, automatically switching to low temperature after 5 minutes of continuous use for scalding protection.
- Warm Air Dryer: Reduces the need for toilet paper by providing a gentle stream of warm air.
- LED Nightlight: Illuminates the toilet bowl for convenience during nighttime use.
- Self-Cleaning Dual Nozzle: Features separate nozzles for posterior and feminine washing, with an automatic self-cleaning function before and after each use.
- Adjustable Spray: Customize water pressure and nozzle position for optimal cleaning.
- Instant Warm Water: Provides on-demand warm water for washing without a separate water tank.
Image 4.1: Overview of the Veken Smart Bidet Toilet Seat, highlighting the spray function, heated seat, warm air dryer, and LED nightlight.
Image 4.2: Illustration of the three distinct cleaning modes: posterior wash, feminine cleaning, and automatic nozzle cleaning.
Image 4.3: Diagram showing the internal components responsible for the heated seat and warm air drying functions.
Image 4.4: The integrated LED night light providing illumination within the toilet bowl.
Image 4.5: Visual representation of the instant warm water heating system, showing water temperature ranges.
5. Installation and Setup
Before starting, ensure you have access to a GFCI electrical outlet near the toilet. The power cord is approximately 3 feet (1 meter) long. If an outlet is not within reach, a GFCI-rated extension cord may be required.
5.1 Pre-Installation Checklist
- Confirm your toilet is an elongated model.
- Ensure a GFCI electrical outlet is available.
- Gather necessary tools: adjustable wrench, screwdriver, towels.
5.2 Step-by-Step Installation
- Turn Off Water Supply: Locate the water shut-off valve behind your toilet and turn it clockwise until the water flow stops. Flush the toilet to drain the tank.
- Remove Existing Toilet Seat: Unscrew and remove your current toilet seat and lid. Clean the toilet bowl rim thoroughly.
- Install T-Adapter: Disconnect the existing water supply hose from the toilet tank. Install the T-adapter onto the toilet tank's water inlet. Reconnect the original water supply hose to one end of the T-adapter.
- Install Mounting Plate: Place the installation template over the toilet bowl holes. Position the mounting plate according to the template, inserting the mounting screws with rubber grommets through the toilet holes. Secure from underneath with plastic wing nuts, ensuring a snug fit without overtightening.
- Attach Bidet Seat: Slide the Veken Smart Bidet Toilet Seat onto the installed mounting plate until it clicks securely into place.
- Connect Bidet Water Hose: Connect the provided bidet water supply hose from the T-adapter to the water inlet on the side of the bidet seat. Hand-tighten first, then use a wrench for a quarter turn to ensure a leak-free seal.
- Restore Water Supply: Slowly turn the toilet's water shut-off valve counter-clockwise to restore water flow. Check for any leaks at all connection points.
- Connect Power: Plug the bidet seat's power cord into the GFCI electrical outlet. The unit will typically beep and the nightlight may activate, indicating it is powered on.
Image 5.1: The Veken Smart Bidet Toilet Seat fully installed on an elongated toilet in a bathroom setting.
6. Operation
The Veken Smart Bidet Toilet Seat is operated via a control panel located on the right side of the seat (when seated). An audible beep will confirm each button press or function activation.
6.1 Control Panel Functions
Image 6.1: Detailed view of the control knob and its various functions for washing, massage, and lighting settings.
- Wash Functions (Control Knob Rotation):
- Rotate forward for Posterior Wash.
- Rotate backward for Feminine Cleaning.
- Center the knob to stop the wash cycle.
- Massage Function (Short Press Knob): While a wash cycle is active, a short press of the control knob will activate the massage function, cycling between minimum, maximum, and mixed spray patterns.
- Lighting Setting (Long Press Knob): A long press of the control knob will adjust the LED nightlight settings.
- Air Dryer (Press Knob after Wash): After a wash cycle, press the control knob to activate the warm air dryer. Press again to stop.
- Temperature Adjustment Buttons: Separate buttons on the side panel allow adjustment of the heated seat, water temperature, and air dryer temperature. Each button typically cycles through Off, Low, and High settings with successive presses.
6.2 Seat Sensor
The bidet seat is equipped with a seat sensor. Wash functions will only activate when a user is seated on the bidet. This prevents accidental spraying when the seat is empty.
7. Maintenance
Regular cleaning and maintenance will ensure the longevity and hygienic operation of your Veken Smart Bidet Toilet Seat.
7.1 Nozzle Cleaning
- The bidet features an automatic self-cleaning function for the nozzles before and after each use.
- For manual cleaning, refer to the control knob functions (Image 6.1) for the 'Nozzle Cleaning' setting, which extends the nozzles for easy wiping. Use a soft cloth and mild soap.
7.2 Seat and Exterior Cleaning
- Disconnect the power cord before cleaning.
- Wipe the exterior surfaces of the bidet seat with a soft, damp cloth and a mild, non-abrasive cleaner.
- Do not use harsh chemicals, abrasive pads, or spray water directly onto the control panel or electrical components.
- The bidet seat can be easily detached from the mounting plate for thorough cleaning of the toilet rim and the underside of the seat.
8. Troubleshooting
If you encounter any issues with your Veken Smart Bidet Toilet Seat, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No water spray | Water supply valve closed; bidet hose kinked; seat sensor not activated. | Open water supply valve; straighten hose; ensure user is properly seated. |
| No heat (water/seat/dryer) | Power cord unplugged; GFCI tripped; temperature setting is 'Off'. | Check power connection; reset GFCI; adjust temperature settings to 'Low' or 'High'. |
| Water leakage | Loose connections; damaged hose/seal. | Tighten all water connections (T-adapter, bidet hose); inspect hoses and seals for damage and replace if necessary. |
| Air dryer not effective | Temperature setting too low; insufficient drying time. | Increase air dryer temperature setting; allow more time for drying. |
| Bidet beeps constantly | Normal operation for function confirmation. | This is an intended feature to confirm actions. There is no option to disable the beeping. |
If the problem persists after attempting these solutions, please contact Veken customer support for further assistance.
9. Specifications
| Feature | Specification |
|---|---|
| Model Number | VK813 |
| Product Dimensions | 50.8 x 37.39 x 8.99 cm |
| Item Weight | 4.13 kg |
| Material | Plastic |
| Color | White |
| Shape | Oval (Elongated) |
| UPC | 850029083016 |
| Power Source | Corded Electric (GFCI required) |
10. Warranty and Support
For warranty information, please refer to the warranty card included with your product or visit the official Veken website. If you require technical support or have questions not covered in this manual, please contact Veken customer service through their official channels.