Sharp Small Digital Alarm Clock User Manual

Introduction

Thank you for purchasing the Sharp Small Digital Alarm Clock. This manual provides detailed instructions for setting up, operating, and maintaining your new alarm clock. Please read this manual thoroughly before use to ensure proper function and longevity of your device.

Product Overview

The Sharp Small Digital Alarm Clock is designed for simplicity and reliability. It features a bright red LED display, easy-to-use top button controls, and a convenient snooze function. It operates on AC power with a battery backup to maintain settings during power outages.

Sharp Small Digital Alarm Clock front view

Figure 1: Front view of the Sharp Small Digital Alarm Clock, showing the red LED display.

Key Features:

0.6-inch Red LED Display for clear visibility.
Easy-to-access Top Button Controls for intuitive operation.
9-Minute Snooze function for extra rest.
AC Powered with Battery Backup (requires 1 x 9V battery, not included) to preserve time and alarm settings during power interruptions.
Compact design, ideal for bedside tables.

Figure 2: Diagram highlighting the 0.6" Red LED Display, Beep Alarm, 9 Minute Snooze, Easy Set Top Button Controls, and Optional Battery Backup.

Dimensions of the Sharp Small Digital Alarm Clock

Figure 3: Product dimensions: 4.63 inches (width) x 1.95 inches (depth) x 2.8 inches (height).

Controls and Display

Familiarize yourself with the clock's controls and display indicators:

Top view of Sharp Digital Alarm Clock showing button labels

Figure 4: Top view of the clock with labels for TIME, ALARM, SNOOZE, HOUR, MIN buttons, and ALARM ON/OFF switch.

TIME Button: Used to enter time setting mode.
ALARM Button: Used to enter alarm setting mode.
SNOOZE Button: Activates the snooze function when the alarm sounds.
HOUR Button: Adjusts the hour in time or alarm setting mode.
MIN Button: Adjusts the minute in time or alarm setting mode.
ALARM ON/OFF Switch: Toggles the alarm function on or off.
PM Indicator: A red dot on the display indicates PM hours.
ALARM Indicator: A red dot on the display indicates the alarm is set.

Setup

Power Connection: Plug the AC power cord into a standard electrical outlet. The LED display will light up.
Battery Backup (Optional but Recommended):
- Locate the battery compartment on the bottom of the clock.
- Insert one 9V battery (not included), observing the correct polarity (+/-).
- Close the battery compartment cover.
Note: The battery backup only maintains time and alarm settings during a power outage; the display will not be lit when operating on battery power alone.

Operating Instructions

Setting the Time:

Press and hold the TIME button. The hour digits will begin to flash.
While holding the TIME button, press the HOUR button repeatedly to advance the hour. Observe the PM indicator for correct AM/PM setting.
While still holding the TIME button, press the MIN button repeatedly to advance the minute.
Release the TIME button to save the set time. The display will stop flashing.

Setting the Alarm:

Press and hold the ALARM button. The alarm hour digits will begin to flash.
While holding the ALARM button, press the HOUR button repeatedly to set the desired alarm hour. Observe the PM indicator.
While still holding the ALARM button, press the MIN button repeatedly to set the desired alarm minute.
Release the ALARM button to save the alarm time. The alarm time will stop flashing.
To activate the alarm, slide the ALARM ON/OFF switch to the "ON" position. A red alarm indicator dot will appear on the display.
To deactivate the alarm, slide the ALARM ON/OFF switch to the "OFF" position. The red alarm indicator dot will disappear.

Using the Snooze Function:

When the alarm sounds, press the large SNOOZE button located on the top of the clock. The alarm will temporarily stop and sound again after approximately 9 minutes.

Turning Off the Alarm:

To turn off the alarm completely after it sounds (without snoozing), slide the ALARM ON/OFF switch to the "OFF" position.

Maintenance

Cleaning: Wipe the clock with a soft, dry cloth. Do not use abrasive cleaners or solvents.
Battery Replacement: Replace the 9V battery annually or if the clock fails to maintain time during a power interruption.
Placement: Place the clock on a stable, flat surface away from direct sunlight, heat sources, and excessive moisture.

Troubleshooting

Problem	Possible Cause	Solution
Display is blank.	No AC power; power outage.	Ensure the power cord is securely plugged into a working outlet. If there's a power outage, the display will remain off even with battery backup.
Alarm does not sound.	Alarm switch is OFF; alarm time not set correctly; volume too low (not applicable for this model).	Slide the ALARM ON/OFF switch to "ON". Verify the alarm time is set correctly (check AM/PM).
Time is incorrect after power interruption.	Battery backup not installed or battery is dead.	Install a fresh 9V battery for backup.

Specifications

Brand: Sharp
Model: B08XMRRBHB
Display Type: Digital LED (Red)
Display Size: 0.6 inches
Power Source: Corded Electric, Battery Powered (1 x 9V battery, not included)
Product Dimensions: 4.63" (W) x 1.95" (D) x 2.8" (H)
Weight: 7.8 ounces
Special Features: Snooze, Battery Backup
Material: Plastic

Warranty and Support

For warranty information or technical support, please refer to the warranty card included with your product or visit the official Sharp website. Keep your purchase receipt as proof of purchase.

Manufacturer: SHARP

	Sharp SPC276 Digital Alarm Clock with Bluetooth & Sleep Sounds: User Guide Comprehensive guide to operating the Sharp SPC276 Digital Alarm Clock, covering features, setup, alarm functions, Bluetooth connectivity, sleep sounds, and safety precautions.
	Sharp Atomic Clock SPC1019 Instructions and Warranty User manual and warranty information for the Sharp Atomic Clock SPC1019, detailing setup, time setting, alarm functions, and troubleshooting.
	SHARP SPC189/SPC193 LED Alarm Clock with USB Port: Instruction Manual & Warranty Official instruction manual and warranty information for the SHARP SPC189 and SPC193 LED Alarm Clock with USB charging ports. Learn how to set time, alarm, use snooze, USB charging, and safety precautions.
	SPC268 Sunrise Alarm Clock with USB Port: Instruction Manual & Warranty Official instruction manual and warranty information for the SHARP SPC268 Sunrise Alarm Clock with USB Port. Learn how to set the clock, alarms, use the sunrise and color-changing lights, and understand safety precautions.
	SHARP SPC543 Projection Alarm Clock with USB Port - Instruction Manual Official instruction manual and warranty information for the SHARP SPC543 Projection Alarm Clock with USB Port. Learn how to set the clock, alarm, date, use the projection feature, and understand safety instructions.
	SHARP SPC500 LCD Digital Alarm Clock User Manual and Instructions Official user manual and instructions for the SHARP SPC500 LCD Digital Alarm Clock. Learn how to set the time, set the alarm, use the snooze and backlight features, and understand power supply and battery warnings. Includes FCC information.

Sharp B08XMRRBHB