ViandPro 90cm 6 Burner Gas Hob

1. Important Safety Information

Please read this manual carefully before installing or using your gas hob. Keep this manual for future reference. Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer, service agency, or the gas supplier.

• Gas Safety: Ensure adequate ventilation when operating the gas hob. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Children and Pets: Keep children and pets away from the appliance during operation. Surfaces can become very hot.
• Hot Surfaces: The hob surface, pan supports, and burner caps will become hot during use. Allow them to cool before cleaning or touching.
• Gas Leaks: If you smell gas, immediately shut off the gas supply to the appliance, open windows and doors, and do not operate any electrical switches. Contact your gas supplier or a qualified technician.
• Automatic Shut Off & Ignition: This appliance features automatic shut-off and automatic ignition for enhanced safety and convenience.

2. Setup and Installation

The ViandPro 90cm Gas Hob is designed for drop-in installation. Proper installation is crucial for safe and efficient operation. It is recommended that installation be carried out by a qualified professional.

2.1 Unpacking

• Carefully remove the hob from its packaging.
• Check for any damage during transit. Report any damage to your supplier immediately.
• Ensure all components are present, including the LPG Kit and Warranty Card/Information.

2.2 Dimensions and Cut-out

Refer to the diagram below for precise dimensions and the required countertop cut-out for installation.

Image: Installation dimensions for the ViandPro 90cm Gas Hob. The overall hob dimensions are approximately 915mm width by 510mm depth. The required cut-out dimensions are between 830-860mm width and 490mm depth. A minimum clearance of 65mm from the rear wall and 30mm from side walls is indicated.

• Overall Hob Dimensions: Approximately 915mm (width) x 510mm (depth).
• Countertop Cut-out: 830-860mm (width) x 490mm (depth).
• Clearances: Ensure a minimum clearance of 65mm from the rear wall and 30mm from side walls.

2.3 Gas and Electrical Connections

• Gas Connection: This appliance is designed for gas fuel. An LPG Kit is included for conversion if required. All gas connections must comply with local regulations and be performed by a qualified gas fitter.
• Electrical Connection: The hob requires an electrical supply for the automatic ignition system. Ensure the electrical connection is made by a qualified electrician and complies with local wiring regulations.

3. Operating Instructions

Your ViandPro gas hob features 6 burners, including 2 dual wok burners, and cast iron supports for stable cooking.

Image: Top-down view of the ViandPro 90cm 6 Burner Stainless Steel Gas Hob, showing the layout of the six burners and front-mounted control knobs.

3.1 Ignition

The hob is equipped with an electronic ignition system.

1. Ensure a suitable pan is placed centrally on the chosen burner's cast iron support.
2. Push down the corresponding control knob and turn it counter-clockwise to the maximum flame setting (large flame symbol).
3. Hold the knob down for a few seconds until the flame ignites and stabilizes. If the flame extinguishes, repeat the process.
4. Once ignited, release the knob.

Image: Close-up view of the brushed stainless steel control knobs on the ViandPro gas hob, showing the symbols for ignition and flame adjustment.

3.2 Flame Adjustment

• After ignition, you can adjust the flame size by rotating the control knob between the maximum (large flame symbol) and minimum (small flame symbol) settings.
• For dual wok burners, the control knob allows for independent control of the inner and outer rings, providing versatile heat options for different cooking needs.
• Always ensure the flame is stable and does not extend beyond the base of the pan.

3.3 Turning Off

To turn off a burner, rotate the control knob clockwise until it clicks into the 'off' position (dot symbol).

4. Maintenance and Cleaning

Regular cleaning and maintenance will ensure the longevity and optimal performance of your gas hob.

• Before Cleaning: Always ensure the hob is completely cool and the gas supply is turned off at the main valve before cleaning.
• Stainless Steel Surface: Clean the brushed stainless steel surface with a soft cloth and a mild, non-abrasive cleaner specifically designed for stainless steel. Wipe in the direction of the grain to avoid streaks.
• Cast Iron Supports: The cast iron pan supports can be removed for cleaning. Wash them with warm soapy water, rinse thoroughly, and dry completely before replacing.
• Burner Caps and Rings: Remove the burner caps and rings. Clean them with warm soapy water and a soft brush if necessary. Ensure they are completely dry before reassembling them onto the hob.
• Ignition Electrodes: Keep the ignition electrodes clean and free from food debris to ensure reliable ignition. Use a small, dry brush if needed.
• Avoid: Do not use abrasive cleaners, scourers, or harsh chemicals as these can damage the hob's surface.

5. Troubleshooting

If you encounter issues with your gas hob, refer to the following common problems and solutions. If the problem persists, contact a qualified technician.

6. Specifications

Detailed technical specifications for the ViandPro 90cm 6 Burner Gas Hob (Model VP-H906SS).

7. Warranty and Support

Your ViandPro gas hob comes with a warranty. Please refer to the 'Warranty Card/Information' included in the packaging for details regarding the warranty period, terms, and conditions.

For technical support, service, or to inquire about spare parts, please contact the retailer where you purchased the appliance or the manufacturer directly. Ensure you have your model number (VP-H906SS) and purchase details ready when contacting support.