Atova International Caravaggio Decorative Stucco Micro Plaster User Manual

1. Product Overview

The Atova International Caravaggio Decorative Stucco Micro Plaster is a premium interior wall finish designed to create elegant, soft, and light-effect surfaces reminiscent of ancient wall fabrics. This product allows for unique decorative results through varied application techniques, suitable for diverse interior environments. It combines the velvet effect of Venetian plaster with distinctive light play.

Image 1: The product container for Atova International Caravaggio Decorative Stucco Micro Plaster, showing the "Velvet Effect Decorative Stucco" label.

2. Safety Information

Always read and follow all safety instructions on the product label before use. Wear appropriate personal protective equipment (PPE) including gloves and eye protection. Ensure adequate ventilation in the work area. Keep out of reach of children and pets. Do not ingest. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Dispose of unused product and waste materials according to local regulations.

3. Preparation and Tools

3.1 Required Tools and Materials:

• Atova PVC Spatula or similar trowel
• Brush or roller for fixative application
• Sandpaper or sanding block
• Joint compound (if needed for imperfections)
• Universal Fixative (diluted with water)
• Clean cloths
• Personal Protective Equipment (PPE): gloves, eye protection

3.2 Surface Preparation:

1. Clean the Surface: Ensure the wall surface is clean, dry, and free from dust, grease, and loose particles.
2. Repair Imperfections: Sand any rough areas and level any imperfections or cracks using joint compound. Allow the compound to dry completely according to its manufacturer's instructions.
3. Apply Fixative: Apply a coat of Universal Fixative, diluted with water (ratio 1:R to 10:R, where 'R' is the recommended dilution ratio for the specific fixative), evenly to the entire surface using a brush or roller.
4. Allow to Dry: Let the fixative dry for approximately four hours before proceeding.

4. Application Instructions ("Spatolato Effect")

The Caravaggio Decorative Stucco is applied using a specific technique to achieve its unique "Spatolato Effect."

1. First Coat Application: Apply the first coat of product with an Atova PVC spatula. The thickness of this coat should be approximately 0.5 to 1 mm. Aim for an even distribution across the surface.
2. First Coat Drying Time: Allow the first coat to dry for about 6-8 hours. Ensure the surface is completely dry before applying the second coat.
3. Second Coat Application: Apply the second coat in small sections, approximately one square meter at a time. Immediately after applying a section, gently go back over the applied surface using the PVC trowel/spatula. Use varied directions and movements to create the desired decorative effect.
4. Continue Application: Continue this process across the entire surface, working in small, manageable sections to maintain control over the decorative finish.

Image 2: An example of a finished wall showcasing the gold Caravaggio Decorative Stucco Micro Plaster with its characteristic velvet and light effects.

4.1 Spread Rate:

The estimated spread rate for this product is 40-50 square feet per liter.

5. Maintenance

Once cured, the Caravaggio Decorative Stucco provides a durable finish. For cleaning, gently wipe the surface with a soft, damp cloth. Avoid abrasive cleaners or harsh scrubbing, as these can damage the decorative finish. For stubborn marks, a mild, pH-neutral cleaner diluted in water may be used, followed by wiping with a clean, damp cloth.

6. Troubleshooting

• Uneven Finish: This can occur if the product is not applied consistently or if the trowel technique is not varied enough. Ensure even pressure and varied strokes during the second coat application. Practice on a small, inconspicuous area first.
• Poor Adhesion: Often caused by inadequate surface preparation. Ensure the surface is clean, dry, and properly primed with a fixative as instructed.
• Cracking: May result from applying coats too thickly or insufficient drying time between coats. Adhere strictly to the recommended thickness and drying times.
• Color Variation: Ensure thorough mixing of the product before use. Apply consistently across the entire surface.

7. Specifications

8. Warranty and Support

Specific warranty information for the Atova International Caravaggio Decorative Stucco Micro Plaster is not provided in the product details. For warranty inquiries or technical support, please contact Atova International directly through their official website or customer service channels.