Transformers Studio Series 86-09 Wreck-Gar Action Figure Instruction Manual

Introduction

This manual provides detailed instructions for the assembly, transformation, and care of your Transformers Studio Series 86-09 Wreck-Gar Voyager Class action figure. Wreck-Gar converts between robot and motorcycle modes, inspired by his appearance in The Transformers: The Movie (1986).

Safety Information

WARNING: CHOKING HAZARD – Small parts may be generated. Not for children under 3 years.

Please ensure all small parts are kept away from young children. Adult supervision is recommended during play, especially during transformation.

What's in the Box

• Wreck-Gar Action Figure (Robot Mode)
• Armor Axe Accessory
• 2 Wheel Accessories

The figure is packaged in robot mode with accessories. The removable backdrop is for display purposes and not part of the figure's functional components.

Image: Wreck-Gar figure in robot mode, showcasing the main figure along with its Armor Axe and two wheel accessories.

Setup and Initial Assembly

Your Wreck-Gar figure comes pre-assembled in robot mode. No complex assembly is required out of the box.

1. Carefully remove the figure and its accessories from the packaging.
2. The Armor Axe can be held in either of Wreck-Gar's hands. The two wheel accessories can be stored on the figure in robot mode or used during transformation.

Image: Wreck-Gar in robot mode, ready for display or transformation. The backdrop is removable.

Operating: Transformation Instructions

Wreck-Gar converts between robot and motorcycle modes in 22 steps. Follow these instructions carefully to ensure a smooth transformation.

Robot Mode to Motorcycle Mode

1. Remove all accessories (Armor Axe, wheels) from the figure. Set them aside.
2. Fold the robot's feet upwards into the lower legs.
3. Rotate the waist 180 degrees.
4. Collapse the robot's chest section downwards, aligning it with the waist.
5. Extend the arms outwards and rotate them to prepare for motorcycle handlebars.
6. Fold the robot's head back into the chest cavity.
7. Bring the shoulder sections together to form the front of the motorcycle.
8. Position the lower legs to form the rear section and exhaust pipes of the motorcycle.
9. Attach the two wheel accessories to the designated pegs on the front and rear of the motorcycle chassis.
10. Secure all panels and tabs to ensure the motorcycle mode is compact and stable.

Image: Wreck-Gar in its complete motorcycle mode. The Armor Axe can be stored on the rear of the vehicle.

Motorcycle Mode to Robot Mode

To convert Wreck-Gar back to robot mode, reverse the steps above:

1. Remove the wheel accessories from the motorcycle chassis.
2. Unclip and separate the motorcycle panels, starting from the rear section.
3. Extend the lower legs and rotate the feet downwards.
4. Unfold the robot's head from the chest cavity.
5. Separate the front motorcycle section to form the robot's arms and shoulders.
6. Rotate the waist 180 degrees to align the robot's torso.
7. Extend the chest section upwards.
8. Ensure all joints are locked into place for a stable robot mode.
9. Re-attach the Armor Axe to Wreck-Gar's hand if desired.

Image: Wreck-Gar in robot mode, posed with its Armor Axe and one wheel accessory, demonstrating accessory integration.

Maintenance

Cleaning

To clean your Wreck-Gar figure, gently wipe it with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid harsh chemicals or abrasive cleaners, as these can damage the paint and plastic.

Storage

Store the figure in a cool, dry place away from direct sunlight and extreme temperatures. Prolonged exposure to sunlight can cause discoloration. Keep small accessories in a secure container to prevent loss.

Troubleshooting

• Parts not aligning during transformation: Ensure all previous steps have been completed correctly. Gently apply pressure to snap parts into place, but do not force them. Refer to the transformation steps again.
• Loose joints: Over time, some joints may become slightly loose. This is normal with repeated use.
• Lost accessories: Keep all small accessories in a designated storage area when not in use to prevent loss.

Specifications

Image: Dimensional diagram of Wreck-Gar in motorcycle mode, illustrating its length, width, and height.

Warranty Information

Specific warranty details for your Transformers Studio Series 86-09 Wreck-Gar figure are typically provided by the manufacturer, Hasbro, at the time of purchase or within the product packaging. Please refer to any included documentation for comprehensive warranty terms and conditions.

Customer Support

For further assistance, questions, or to report any issues with your Transformers Wreck-Gar figure, please contact Hasbro customer support. You can typically find contact information on the official Hasbro website or through the customer service details provided in the product packaging.

Official Transformers Website: Visit the Transformers Store on Amazon