ASONPAO CMXZDCG453 Universal Garage Door Opener Remote Manual

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your ASONPAO CMXZDCG453 Universal Garage Door Opener Remote. This remote is designed for universal replacement and is compatible with various Sears Craftsman, Liftmaster, and Chamberlain garage door openers produced from 1993 to current, featuring Yellow, Purple, Red/Orange, or Green Learn buttons. Please read this manual thoroughly before use to ensure proper functionality and safety.

Note: This remote does not support dip switch garage door openers.

2. Safety Information

• Keep the remote control out of reach of children.
• Operate the garage door only when it is in full view and free of obstructions.
• Do not allow children to play with the garage door opener or remote control.
• Ensure the garage door is fully closed before leaving the premises.
• If the garage door opener does not activate, do not repeatedly press the remote button. Refer to the troubleshooting section.

3. Package Contents

Your package should contain the following items:

• ASONPAO Universal Garage Door Opener Remote (2 units)
• CR2032 Lithium Batteries (pre-installed)
• Visor Clip
• User Manual

4. Product Overview

The ASONPAO CMXZDCG453 remote features a compact design with three buttons for controlling up to three different garage door openers. It includes an LED indicator for programming feedback and operates on a 240mAh lithium battery for extended life. The remote utilizes Rolling Code technology for enhanced security.

Image: ASONPAO Universal Garage Door Opener Remote, showing its three buttons and compact design.

5. Setup and Programming

Follow these steps to program your ASONPAO universal remote to your garage door opener.

5.1. Choose Garage Door Opener Type

1. Press and hold buttons 2 and 3 on the remote simultaneously until the remote's LED goes OFF (approximately 3 seconds). Then release the buttons. The remote is now in programming mode.
2. Press and release the desired remote control button (1, 2, or 3) the number of times that corresponds to your garage door opener type:
   • 1 time: 891LM Yellow Learn Button (2011-Current)
   • 2 times: 371LM Purple Learn Button (2005-Current 315mhz)
   • 3 times: 971LM Orange or Red Learn Button (1997-2005 390mhz)
   • 4 times: 81LM Green Learn Button (1993-1996 390mhz)
   • 5 times: Genie Overhead Door Intellicode (1995-Current 315mhz)
   • 6 times: Genie Overhead Door Intellicode (2005-Current 390mhz)
   • 7 times: Linear Mega-Code (1997-Current 318mhz)
3. Once you have finished programming, wait approximately 3 seconds. The remote's LED will flash, then turn OFF, indicating that programming mode has automatically exited and programming is complete.

Image: Visual guide for programming the remote, showing how to enter programming mode and select the garage door opener type based on the learn button color.

Image: Chart detailing universal compatibility with Liftmaster, Chamberlain, and Sears Craftsman garage door openers, categorized by learn button color and year of manufacture.

5.2. Sync Remote with Garage Door Opener

1. Press and release the "Learn" button on your garage door opener. The learn LED light will glow steadily for 30 seconds.
2. Within 30 seconds, get close to your garage door opener and press the programmed button of your remote. The garage door opener lights will flash or two clicks will be heard, indicating that it has learned the code.
3. To test, press the programmed remote button. The garage door opener should activate. If the opener does not activate, repeat the above programming steps.

6. Operating Instructions

Once programmed, simply press the corresponding button on your ASONPAO remote to open or close your garage door. The remote offers a control range of up to 164 feet.

7. Maintenance

7.1. Battery Replacement

The remote uses a CR2032 lithium battery. When the remote's range decreases or the LED indicator does not light up, it's time to replace the battery. To replace, carefully open the remote casing, remove the old battery, and insert a new CR2032 battery with the positive (+) side facing up. Ensure the battery is securely seated before closing the casing.

Image: Diagram illustrating how to open the remote and replace the CR2032 battery.

8. Troubleshooting

If your remote does not sync with the garage door opener, consider the following solutions:

• Solution 1: Double-check the exact color of the learn button on your garage door opener and ensure you selected the correct programming sequence for that type.
• Solution 2: Make sure your garage door opener is fully closed before starting the programming process. Otherwise, programming may fail. Get close to the garage door opener when pressing the programmed remote button.
• Solution 3: Perform the programming steps quickly. If you wait too long (a few seconds) between steps, the process may time out and programming will fail.
• Solution 4: The memory of your garage door opener might be full. Press and hold the learn button on the garage door opener for several seconds until the LED turns OFF. This clears all memory. Then, re-program the remote with the garage door opener again.

9. Specifications

10. Warranty and Support

The ASONPAO CMXZDCG453 Universal Garage Door Opener Remote comes with a 3-year warranty. For any technical assistance or support, please contact ASONPAO customer service. 24-hour Amazon technical support is also available.