SOCAL-LED LIGHTING Arrow LED Tailgate Running Light Kit, Model LTLK-05-60 User Manual

1. Introduction

Thank you for choosing the SOCAL-LED LIGHTING Arrow LED Tailgate Running Light Kit. This manual provides detailed instructions to ensure proper installation, safe operation, and effective maintenance of your new LED tailgate light strip. Please read this manual thoroughly before installation and use.

2. Safety Information

• Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits or electrical shock.
• Ensure all wiring connections are secure and properly insulated to prevent moisture ingress and electrical issues.
• Do not modify the product in any way not described in this manual. Unauthorized modifications may void the warranty and create safety hazards.
• Verify local regulations regarding vehicle lighting before installation to ensure compliance.
• Keep the product away from excessive heat sources or open flames.

3. Package Contents

The package should contain the following items:

• 1x SOCAL-LED LIGHTING Arrow LED Tailgate Running Light Kit (60 Inch)
• 1x 4-Prong Plug Connector
• Additional mounts and screws (for optional secure installation)

4. Product Specifications

5. Installation Guide

The SOCAL-LED Tailgate Light Kit is designed for easy installation. Follow these steps for a secure and functional setup.

5.1 Preparation

• Ensure the vehicle's ignition is off and the battery is disconnected.
• Clean the mounting surface on the tailgate thoroughly to ensure proper adhesion of the light strip.
• Test the light strip functions before permanent installation by temporarily connecting it to the vehicle's power source.

5.2 Mounting the Light Strip

The light strip features a strong adhesive backing for easy attachment.

1. Carefully peel off the protective film from the adhesive backing of the LED strip.
2. Position the light strip along the bottom edge of your truck's tailgate, ensuring it is centered and straight.
3. Press firmly along the entire length of the strip to ensure strong adhesion.
4. For additional security, use the provided mounts and screws to fasten the strip more permanently.

Image: The SOCAL-LED LIGHTING Arrow LED Tailgate Running Light Kit, showing the flexible strip with arrow-shaped LEDs and wiring harness.

Image: Close-up of the LED strip showing the adhesive backing being peeled off, illustrating the easy peel-and-stick installation method.

5.3 Wiring Connections

Connect the 4-pin flat connector to your vehicle's existing trailer wiring harness. If your vehicle does not have a 4-pin connector, you will need to hardwire the connections according to the diagram below.

Image: Detailed wiring diagram for the 4-pin connector, showing connections for Right Turn/Brake, Left Turn/Brake, Running (70% Brightness), and Ground.

• Green Wire: Connect to Right Turn Signal / Brake Light.
• Yellow Wire: Connect to Left Turn Signal / Brake Light.
• Brown Wire: Connect to Running Lights (70% Brightness).
• White Wire: Connect to Ground.

Ensure all connections are secure and protected from the elements. Reconnect the vehicle battery once wiring is complete.

6. Operating Instructions

The LED tailgate light strip offers multiple lighting functions for enhanced visibility and safety.

6.1 Lighting Functions

• Running Lights: All red LEDs illuminate at 70% brightness when headlights are on.
• Brake Light: All red LEDs illuminate at full brightness with an exclusive strobe (flashing) effect when the brake pedal is pressed.
• Left Turn Signal: Sequential amber LEDs illuminate from the center to the left.
• Right Turn Signal: Sequential amber LEDs illuminate from the center to the right.
• Double Flashing (Hazard Lights): All amber LEDs flash simultaneously.

Image: Visual representation of the light strip's various modes: brake light (solid red), running light (dim red with arrows), left turn signal (sequential amber left), and right turn signal (sequential amber right).

6.2 Steering Priority Function

The light strip incorporates a steering priority function:

• If a turn signal or double flashing light is active, the brake light function will be temporarily overridden.
• To activate the brake light normally, the turn signal or double flashing light must be deactivated first.
• When braking while a turn signal is active, the turn signal will temporarily stop, and the light bar will display the strobe flashing red brake light. Once the brake is released, the turn signal (yellow) will resume.

7. Maintenance

• Cleaning: Clean the light strip periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or high-pressure washers directly on the strip.
• Inspection: Regularly inspect the wiring and connections for any signs of wear, corrosion, or damage. Ensure the adhesive remains secure.
• Waterproof Design: The light strip features an IP67 waterproof rating, making it resistant to snow, dust, and sand. However, avoid prolonged submersion.

Image: Illustration highlighting the IP68 waterproof and durable design of the LED tailgate light strip, showing water splashing over it.

8. Troubleshooting

9. Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact SOCAL-LED LIGHTING customer service directly. Keep your purchase receipt as proof of purchase.