AEGIS Fireproof Safe User Manual

1. Introduction

The AEGIS 2.6 Cubic Feet Fireproof Safe is designed to provide secure storage for your valuables, documents, and other important items. Featuring a digital electronic lock keypad and a robust construction, this safe offers both convenience and protection against fire and theft. Its spacious interior with removable shelves allows for flexible organization of your belongings.

Figure 1: AEGIS 2.6 Cubic Feet Fireproof Safe

2. Key Features

• Fire Resistance: Rated for 30 minutes at 1400°F/760℃ to protect contents from fire. Heat-activated door seal expands to keep out heat and smoke.
• Spacious Interior: 2.6 cubic feet capacity (Internal Size: 15.7"W x 11"D x 17.3"H) with two removable and adjustable shelves for organized storage of cash, documents, jewelry, and more.
• Digital Electronic Lock: Quick setup and easy operation with a digital keypad. Includes 2 backup keys for emergency access.
• Solid Steel Construction: Equipped with 4 φ22*27mm living locking bolts, a pry-resistant thicker steel door, and pry-resistant hinges for advanced theft protection.
• Fully Upholstered Interior: Protects valuables from scratches and damage.
• Dual Power Options: Operates on 4 AA alkaline batteries (not included) or via an included USB-C cable for alternative power.
• Easy Installation: Pre-drilled holes on the back and bottom with included mounting bolts for secure floor or wall mounting.

Figure 2: Fireproof Construction Layers

Figure 3: Enhanced Security Features

3. Setup

3.1 Initial Opening and Battery Installation

1. Locate the emergency backup keys. These are typically found in a small bag inside the safe or attached to the packaging. Keep them in a secure location outside the safe.
2. Insert one of the backup keys into the keyhole located behind the digital keypad cover. Turn the key clockwise while simultaneously turning the knob to open the safe door.
3. Once the safe is open, locate the battery compartment on the inside of the door. Insert 4 AA alkaline batteries (not included) into the compartment, ensuring correct polarity.
4. Close the battery compartment cover.

3.2 Setting Your Personal Code

1. With the safe door open, press the red reset button located on the inside of the door, near the hinge. You will hear a beep.
2. On the digital keypad, enter your desired 3-8 digit personal code.
3. Press the "LOCK" button to confirm your new code. You will hear a confirmation beep.
4. Test your new code with the door open to ensure it works correctly before closing the safe. Enter your code, then turn the knob to confirm the lock mechanism retracts.

Figure 4: Digital Keypad and Knob

Figure 5: Removable and Adjustable Shelf Configuration

4. Operating the Safe

4.1 Opening the Safe

1. Enter your 3-8 digit personal code on the digital keypad.
2. Press the "LOCK" button. If the code is correct, the green "PASS" light will illuminate, and you will hear a beep.
3. Within 5 seconds, turn the knob clockwise to open the safe door.

4.2 Closing and Locking the Safe

1. Close the safe door firmly.
2. Turn the knob counter-clockwise to engage the locking bolts. The safe is now securely locked.

4.3 Emergency Access

In case of forgotten password or dead batteries, you can access the safe using the backup key or the USB-C emergency power supply.

1. Using Backup Key: Insert the backup key into the keyhole behind the keypad cover. Turn the key clockwise and simultaneously turn the knob to open the safe.
2. Using USB-C Emergency Power: Connect the included USB-C cable to the USB-C port on the keypad panel and to an external power bank (not included). This will power the keypad, allowing you to enter your code and open the safe.

Figure 6: USB-C Emergency Power Port

5. Installation

The AEGIS safe can be securely mounted to the floor or wall using the pre-drilled holes and included mounting bolts. This prevents unauthorized removal of the safe.

Important Safety Warning: DO NOT DRILL FROM ANY LOCATION INSIDE THE SAFE.

1. Unlock and open the safe door. Look to the bottom or the back of the safe for two indentations indicating the pre-drilled holes.
2. Use a screw to mark the floor or wall through these holes. Move the safe aside to clearly see both marked spots for drilling.
3. Drill into the floor or wall at the marked locations.
4. Replace the safe in the desired position, aligning the holes in the safe with those in the floor or wall.
5. Pass each tap screw through a washer, then through the safe and into a masonry anchor. Tighten with the wrench. Place masonry anchors into the holes in the floor or wall.

Figure 7: Safe Installation Steps

6. Maintenance

6.1 Battery Replacement

When the "LOW" battery indicator light illuminates on the keypad, it is time to replace the batteries. Use 4 new AA alkaline batteries. Do not mix old and new batteries or different types of batteries. Replace all batteries at the same time.

6.2 Cleaning

Clean the exterior of the safe with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish. Do not use water directly on the keypad or electronic components.

7. Troubleshooting

8. Specifications

9. Warranty and Support

AEGIS is committed to providing high-quality products and excellent customer service. For any questions, concerns, or warranty claims regarding your safe, please contact AEGIS customer support directly. While specific warranty details may vary, the manufacturer is known for responsive assistance.

Please refer to the product packaging or the official AEGIS website for the most current contact information and detailed warranty policy.