GOOLOO GP80 800A Peak SuperSafe Car Jump Starter User Manual

1. Introduction

Thank you for choosing the GOOLOO GP80 800A Peak SuperSafe Car Jump Starter. This portable and powerful device is designed to jump start 12V vehicles with up to 4.5L gas engines, and can also serve as a portable power bank for charging various electronic devices. Please read this manual carefully before use to ensure safe and optimal performance.

Image: The GOOLOO GP80 jump starter connected to a car battery, demonstrating its primary function.

2. Important Safety Information

Always observe the following safety precautions when using the GOOLOO GP80 jump starter:

• Do not immerse the unit in water or expose it to rain.
• Do not operate the unit if it has been severely damaged or dropped.
• Do not disassemble the unit. Only qualified service personnel should repair this device.
• Do not use the jump starter to charge non-rechargeable batteries.
• Ensure proper ventilation during use.
• Keep out of reach of children.
• Wear eye protection when working near batteries.
• Connect the clamps correctly: Red to Positive (+) and Black to Negative (-). Reverse polarity can cause damage.
• Remove the jump starter from the vehicle battery within 30 seconds after the vehicle starts.

3. Package Contents

Please check the package contents upon opening. If anything is missing or damaged, contact GOOLOO customer support.

• GOOLOO GP80 Jump Starter
• Smart Jumper Clamps
• USB-C Charging Cable
• User Manual
• Storage Case (may vary by package)

Image: The GOOLOO GP80 jump starter unit shown with its smart jumper clamps.

4. Product Features and Components

Familiarize yourself with the different parts of your GP80 jump starter:

• Power Button: Turns the unit on/off and activates the flashlight.
• Battery Level Indicator: LED lights showing the remaining battery capacity.
• USB Output Port (Quick Charge): For charging smartphones, tablets, and other USB-powered devices.
• USB-C Input/Output Port: For charging the jump starter itself or charging other devices.
• 12V Jump Start Port: Connects to the smart jumper clamps.
• LED Flashlight: Provides illumination, with multiple modes (steady, strobe, SOS).

5. Charging the GP80 Jump Starter

Before first use, fully charge the GP80. It is recommended to recharge the unit every 3 months to maintain battery health, even if not used.

1. Connect the provided USB-C charging cable to the USB-C Input/Output port on the GP80.
2. Connect the other end of the USB-C cable to a USB wall adapter (not included) or a powered USB port.
3. The battery level indicator lights will illuminate and flash during charging. All lights will be solid when fully charged.

A full charge typically takes 3-4 hours depending on the power source.

6. Operating Instructions

6.1. Jump Starting a Vehicle

Ensure the GP80 is at least 50% charged before attempting to jump start a vehicle.

1. Connect the Smart Jumper Clamps: Insert the blue plug of the smart jumper clamps into the 12V Jump Start Port on the GP80. Ensure it is fully inserted.
2. Connect to Car Battery:
   • Connect the RED (+) clamp to the positive terminal of the car battery.
   • Connect the BLACK (-) clamp to the negative terminal of the car battery or a solid metal part of the car chassis (unpainted metal).

   The smart clamps have indicator lights and an audible alarm for safety. Refer to the clamp's manual for specific error codes.
3. Start the Vehicle: Once the clamps are correctly connected and the smart clamp indicator light is solid green, start your vehicle's engine.
4. Remove Clamps: As soon as the vehicle starts, remove the smart jumper clamps from the car battery first, then disconnect the blue plug from the GP80.

Important: Do not crank the engine for more than 3 seconds. If the vehicle does not start, wait at least 30 seconds before attempting again. Do not attempt more than 3 consecutive jump starts.

6.2. Charging Mobile Devices

The GP80 can also function as a portable power bank.

1. Connect your device's USB charging cable to either the USB Output Port (Quick Charge) or the USB-C Input/Output Port on the GP80.
2. Connect the other end of the cable to your mobile device.
3. The GP80 will automatically begin charging your device.

6.3. Using the LED Flashlight

The built-in LED flashlight has multiple modes for convenience.

• Press and hold the Power Button for 3 seconds to turn on the flashlight (steady mode).
• Press the Power Button once to switch to Strobe mode.
• Press the Power Button again to switch to SOS mode.
• Press the Power Button once more to turn off the flashlight.

7. Maintenance

Proper maintenance ensures the longevity of your GP80 jump starter.

• Storage: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures. The ideal storage temperature is between -20°C to 60°C (-4°F to 140°F).
• Recharging: Recharge the unit at least once every three months to prevent deep discharge and prolong battery life.
• Cleaning: Use a soft, dry cloth to clean the unit. Do not use harsh chemicals or abrasive materials.
• Battery Care: Avoid fully discharging the battery frequently. Charge it when the battery indicator shows 2-3 bars.

8. Troubleshooting

9. Specifications

10. Warranty and Support

GOOLOO products come with a standard warranty. For detailed warranty information, product registration, or technical support, please visit the official GOOLOO website or contact their customer service team. Keep your purchase receipt as proof of purchase.

GOOLOO Official Website: www.gooloo.com

Customer Service Email: support@gooloo.com