Introduction
Thank you for choosing the Monkey Loop Floor Prime 5 Guitar and Bass Stand. This stand is designed to securely hold up to five electric or acoustic guitars and basses, keeping your instruments organized and protected. Its robust steel construction, foam padding, and foldable design make it a practical accessory for musicians.
Safety Information
- Ensure all components are securely fastened before placing instruments on the stand.
- Place the stand on a flat, stable surface to prevent tipping.
- Do not overload the stand beyond its intended capacity of five instruments.
- Keep the stand away from high-traffic areas where it might be accidentally bumped.
- Regularly inspect the stand for any signs of wear or damage to padding or structural components.
Package Contents
Please check the package to ensure all components are present:
- Main frame components (base, uprights, neck support bar)
- Foam padding for instrument contact points
- Assembly hardware (screws, bolts, Allen key if required)
- Instruction Manual
Note: The term "Archi" in the original Italian packaging refers to the structural components or padded bars of the stand.
Setup Instructions
Assembly
Follow these steps to assemble your Monkey Loop Floor Prime 5 stand:
- Unpack all components and lay them out on a clean, flat surface.
- Identify the base frame and the two upright support bars.
- Attach the upright support bars to the designated slots on the base frame using the provided hardware. Ensure they are firmly secured.
- Attach the top neck support bar to the upper ends of the upright support bars. This bar typically has the individual padded slots for instrument necks.
- Ensure all screws and bolts are tightened. Do not overtighten.
- Verify the stand is stable and does not wobble.
Figure 1: Fully assembled Monkey Loop Floor Prime 5 stand.
Figure 2: Detail of the foam-padded neck supports.
Figure 3: Detail of the non-slip base and feet.
Operating Instructions
Placing Instruments
To use the stand effectively and safely:
- Gently place the body of your guitar or bass onto the padded lower bar of the stand.
- Ensure the neck of the instrument rests securely in one of the padded slots on the top bar.
- For acoustic guitars, which typically have wider bodies, you may find that the stand comfortably holds fewer than five instruments (e.g., 3-4 acoustic guitars). Electric guitars and basses will generally fit five without issue.
- When removing an instrument, lift it straight up and out of the stand to avoid snagging or bumping adjacent instruments.
Figure 4: Stand with a mix of electric and acoustic guitars.
Figure 5: Side view demonstrating instrument placement.
Folding the Stand
The stand features a simple folding system for storage or transport:
- Remove all instruments from the stand.
- Locate the folding mechanism, typically a latch or pin, near the base of the uprights.
- Release the mechanism and carefully fold the stand flat.
- Ensure the stand is fully collapsed and secured before moving.
Figure 6: The stand in its folded configuration for easy storage.
Maintenance
- Cleaning: Wipe the stand with a soft, dry cloth to remove dust. For stubborn dirt, use a slightly damp cloth and mild soap, then dry thoroughly. Avoid abrasive cleaners.
- Padding Care: Inspect the foam padding regularly for tears or wear. Replace if necessary to ensure continued instrument protection.
- Hardware Check: Periodically check all screws and bolts to ensure they remain tight. Retighten as needed to maintain stability.
- Storage: When not in use, store the stand in a dry environment, preferably folded, to prolong its lifespan.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand is wobbly or unstable. | Loose assembly hardware; uneven surface. | Ensure all screws and bolts are tightened. Move the stand to a flat, level surface. |
| Rubber/foam padding detaches. | Adhesive failure; excessive friction. | Re-secure padding with a strong adhesive suitable for foam/rubber. |
| Instruments do not fit well (especially acoustic). | Stand designed primarily for electric guitars; limited spacing for wider bodies. | Adjust instrument placement; consider reducing the number of acoustic guitars on the stand. |
| Missing assembly parts (e.g., bolt). | Packaging error. | Contact customer support for replacement parts. |
Specifications
| Feature | Detail |
|---|---|
| Brand | MONKEY LOOP |
| Model Name | Prime 5 (10176055) |
| Material | Alloy Steel |
| Dimensions (LxWxH) | 15 x 11 x 62 cm (approximately 5.9 x 4.3 x 24.4 inches) |
| Item Weight | 2 Kilograms (approximately 4.4 lbs) |
| Capacity | 5 Instruments (Guitars or Basses) |
| Finish Type | Painted |
| Special Features | Foam padded, Scratch resistant, Foldable design, Non-slip base |
| Country of Origin | China |
Warranty and Support
Warranty: The product warranty information is not explicitly provided in the product details. Please refer to your purchase receipt or contact the retailer/manufacturer directly for specific warranty terms and conditions.
Support: For any questions, technical assistance, or to report missing parts, please contact Monkey Loop customer support through their official website or the retailer from whom you purchased the product. Have your model number (Prime 5 / 10176055) and purchase details ready.