Introduction
The Monkey Loop Floor Prime 3 Guitar Stand is designed to securely hold up to three acoustic, electric, or bass guitars. Constructed from durable alloy steel with protective rubber padding, this stand offers a compact and stable solution for organizing your instruments in a studio, on stage, or at home. Its foldable design allows for easy transport and storage.
Safety Information
- Ensure all components are securely fastened before placing instruments on the stand.
- Place the stand on a flat, stable surface to prevent tipping.
- Do not exceed the capacity of three guitars.
- Keep the stand away from high-traffic areas to avoid accidental bumps.
- Regularly inspect the stand for any signs of wear or damage to the frame or padding.
Package Contents
Before assembly, verify that all parts are present:
- Main frame components (vertical supports, base bars, top support bar)
- Protective rubber padding/sleeves
- Assembly hardware (screws, Allen key) - Note: Some screws may be pre-inserted into the tubular components.
- Rubber feet
Assembly Instructions
Assembly typically takes approximately 15 minutes. Follow these steps carefully:
- Unpack Components: Carefully remove all parts from the packaging. Check inside the tubular sections for any pre-inserted screws or small parts.
- Assemble the Base: Connect the base bars to the vertical support frames. Ensure the rubber padding is correctly oriented to protect the instrument bodies.
- Attach Vertical Supports: Secure the vertical support frames to the assembled base.
- Install Top Support Bar: Attach the top support bar, which features the neck cradles, to the upper section of the vertical supports. Ensure the cradles are facing the correct direction to hold guitar necks.
- Secure All Fasteners: Hand-tighten all screws initially. Once all components are in place, gently tighten them with the provided Allen key. Avoid over-tightening.
- Check for Stability: After initial tightening, place the stand on a flat surface. If it wobbles, slightly loosen all screws, allow the stand to settle so all feet are in contact with the ground, then re-tighten the screws. This ensures proper alignment and stability.
- Attach Rubber Feet: Ensure all rubber feet are securely attached to the bottom of the stand for enhanced stability and floor protection.
Image: Components of the Monkey Loop Floor Prime 3 Guitar Stand, showing its foldable structure for transport or initial assembly.
Image: Close-up of the stand's base, highlighting the protective rubber padding and stable feet.
Image: Detail of the top support bar, showing the individual cradles designed to hold guitar necks securely.
Operating Instructions
Once assembled and stable, the stand is ready for use:
- Placement: Position the stand in a safe location, away from obstacles and foot traffic.
- Loading Guitars: Gently place the body of each guitar onto the padded base of the stand. Ensure the bottom of the guitar rests fully on the padding.
- Securing Necks: Guide the neck of each guitar into one of the top cradles. The cradles are designed to hold the neck securely without damaging the finish.
- Balance: For optimal stability, distribute the weight of the guitars evenly if possible, especially if not all three slots are used.
- Unloading Guitars: Lift the guitar neck out of its cradle first, then carefully lift the guitar body off the padded base.
Image: The Monkey Loop Floor Prime 3 Guitar Stand holding three guitars (electric and acoustic), demonstrating proper instrument placement.
Care and Maintenance
- Cleaning: Wipe the stand with a soft, dry cloth to remove dust. For stubborn dirt, a slightly damp cloth can be used, followed by immediate drying. Avoid abrasive cleaners or solvents.
- Padding Inspection: Periodically check the rubber padding on the base and neck cradles for any signs of wear, tears, or deterioration. Damaged padding should be replaced to prevent instrument damage.
- Fastener Check: Every few months, inspect all screws and connections to ensure they remain tight. Re-tighten if necessary to maintain structural integrity.
- Storage: When not in use for extended periods, the stand can be folded for compact storage. Store in a dry environment.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand wobbles or is unstable | Uneven assembly; loose fasteners; uneven floor surface. |
|
| Guitars do not sit securely | Incorrect placement; damaged padding. |
|
| Missing parts during assembly | Parts overlooked in packaging. |
|
Specifications
| Model Name | Monkey Loop Floor Prime 3 Guitar Stand |
| Model Number | 10176054 |
| Brand | MONKEY LOOP |
| Material | Alloy Steel |
| Finish Type | Polished |
| Color | Multicolor (primarily black with yellow accents) |
| Item Weight | 2 Kilograms |
| Product Dimensions (L x W x H) | 15 x 11 x 62 cm (folded/packaged) |
| Capacity | 3 Guitars (Acoustic, Electric, or Bass) |
| Country of Origin | China |
Warranty and Support
For product support, warranty information, or to inquire about replacement parts, please contact the official distributor:
Madridhifi.com
As the official distributor of Monkey Loop products, Madridhifi.com is committed to providing excellent service and quality support for your equipment and accessories.
Please refer to your purchase documentation for specific warranty terms and contact details.
