MONKEY LOOP Triple Prime Universal 3-Guitar/Bass Floor Stand

Introduction

The MONKEY LOOP Triple Prime is a robust and compact universal floor stand designed to securely hold up to three electric, acoustic, or bass guitars. Crafted from durable alloy steel and featuring protective rubber lining, this stand ensures optimal support and protection for your instruments. Its foldable design allows for easy transport and storage, making it suitable for studio, stage, or home use.

Safety Information

• Always place the stand on a flat, stable, and non-slip surface to prevent tipping.
• Ensure all components are securely tightened before placing instruments on the stand.
• Do not overload the stand beyond its intended capacity of three instruments.
• Verify that instruments are properly seated in both the neck cradle and body supports to prevent accidental falls.
• Keep the stand and instruments away from high-traffic areas where they might be accidentally bumped.
• Keep out of reach of children and pets to prevent accidental injury or damage to instruments.

Package Contents

Please check that all the following components are included in your package:

• MONKEY LOOP Triple Prime Guitar Stand components
• Instruction Manual

Setup Instructions

Follow these steps to assemble your MONKEY LOOP Triple Prime guitar stand:

1. Unfold the Base: Carefully unfold the three legs of the stand's base until they are fully extended and locked into position. Ensure the rubber feet are firmly on the ground.
2. Attach the Main Pole: Insert the main vertical pole into the central hub of the base. Secure it by tightening any provided knobs or screws.
3. Install Body Supports: Attach the lower, padded body support arms to the main pole or base as indicated. These are designed to cradle the bottom of your guitars.
4. Install Neck Supports: Attach the upper, padded neck cradles to the top section of the main pole. These supports are adjustable to accommodate different instrument heights.
5. Adjust Height: Loosen the height adjustment knob on the main pole. Extend the upper section to your desired height, ensuring the neck cradles are high enough to support the instrument necks without the bodies touching the ground. Tighten the knob securely.
6. Final Check: Before placing instruments, gently shake the stand to ensure all connections are stable and tight.

Operating Instructions

Using your MONKEY LOOP Triple Prime stand is straightforward:

1. Placing an Instrument: Gently lift your guitar or bass and place its body onto one of the lower padded support arms. Ensure the instrument's neck rests securely within the corresponding upper padded neck cradle. The stand is designed to hold the instrument upright and stable.
2. Removing an Instrument: Lift the instrument's neck slightly out of the upper cradle, then lift the entire instrument clear of the lower body supports.
3. Capacity: The stand is designed to hold up to three instruments simultaneously. Distribute the weight evenly if possible.

Maintenance

To ensure the longevity and continued performance of your MONKEY LOOP Triple Prime stand, follow these maintenance guidelines:

• Cleaning: Wipe the stand regularly with a soft, dry cloth to remove dust and dirt. Avoid using abrasive cleaners or solvents, as these can damage the finish and rubber padding.
• Padding Inspection: Periodically check the rubber padding on the neck cradles and body supports for any signs of wear, tears, or deterioration. Damaged padding should be replaced to prevent scratching your instruments.
• Tightness Check: Regularly inspect all screws, bolts, and adjustment knobs to ensure they remain tight. Re-tighten any loose fasteners to maintain stability.
• Storage: When not in use for extended periods, or for transport, fold the stand for compact storage. Store in a dry environment away from extreme temperatures.

Troubleshooting

If you encounter any issues with your stand, refer to the following common problems and solutions:

• Stand Instability:
  • Ensure the stand is placed on a completely flat and level surface.
  • Verify that all three legs of the base are fully extended and locked.
  • Check that all assembly screws and the height adjustment knob are securely tightened.
• Instrument Slipping or Not Sitting Correctly:
  • Confirm that the instrument's body is fully seated on the lower supports and its neck is properly cradled in the upper support.
  • Inspect the rubber padding on the supports for any damage or excessive wear that might reduce grip.
  • Ensure the stand's height is adjusted correctly for your instrument, preventing it from being too high or too low.

Specifications

Warranty and Support

For warranty information, technical support, or inquiries regarding your MONKEY LOOP Triple Prime stand, please contact your original retailer or visit the official MONKEY LOOP distributor website. Please retain your proof of purchase for warranty claims.