Eastman Nevercold Hot Water Recirculation Pump Kit

Introduction

The Eastman Nevercold Hot Water Recirculation Pump Kit is designed to provide instant hot water throughout your home, reducing water waste and wait times. This system is specifically engineered for use with standard hot water heater tanks in single-pipe plumbing systems.

Important Note: This kit is not compatible with tankless water heaters and requires an electrical outlet for operation.

Product Overview and Components

The Nevercold recirculating pump kit includes all necessary components for installation and operation:

• Stainless Recirculating Pump: Features a 3/4 inch FNPT union and an integrated built-in timer.
• Power Cord: A 10-foot power cord for connecting the pump to an electrical outlet.
• Bronze Aqua Flash Bypass Valve: Includes a check valve for efficient water flow.
• Braided Water Supply Line: A 12-inch braided line for connection.
• Tee: For plumbing connections.

Image: All components of the Eastman Nevercold Hot Water Recirculation Pump Kit, including the pump, Aqua Flash valve, braided supply line, and tee.

Image: The Eastman Nevercold Universal Hot Water Recirculation Pump Kit, highlighting its purpose to provide hot water when needed.

Image: Visual representation of the system's easy installation and cost-saving benefits, including water and energy savings.

Setup and Installation

The circulating pump is designed for straightforward installation, typically completed within 30 minutes. It is ideal for homes with standard single-pipe plumbing systems up to 250 feet in length.

Installation Steps (General Guidance):

1. Preparation: Ensure the water heater is turned off and the water supply to the house is shut off. Drain hot water lines to relieve pressure.
2. Pump Placement: Install the stainless recirculating pump directly on your hot water heater tank's hot outlet.
3. Bypass Valve Installation: Install the bronze Aqua Flash bypass valve with check valve at the fixture furthest from the water heater (e.g., under a sink).
4. Connections: Use the provided 12-inch braided water supply line and tee to make the necessary plumbing connections between the hot and cold water lines at the bypass valve location.
5. Electrical Connection: Connect the 10-foot power cord to the pump and plug it into a standard electrical outlet.
6. System Activation: Restore water supply and power to the water heater. Check for leaks.

Caution: Always consult a qualified plumber if you are unsure about any installation steps. Ensure all connections are secure to prevent leaks.

Image: A schematic diagram illustrating how the Nevercold Circulator with built-in timer and the Nevercold Valve, Tee & Hose integrate into a typical tank system plumbing setup.

Operating Instructions

The Eastman Nevercold pump features an integrated built-in timer. This timer allows you to program the pump to activate only during specific periods when hot water is typically needed, optimizing energy efficiency and hot water availability.

Setting the Timer:

Refer to the timer dial on the pump unit. The dial typically has segments representing hours of the day. Push in the pins corresponding to the times you want the pump to operate. Ensure the current time is set correctly on the dial.

Image: A close-up view of the pump unit, clearly showing the integrated timer dial for scheduling operation.

When the pump is active, it circulates hot water from your water heater through the hot water lines and back, ensuring hot water is readily available at your faucets without significant delay.

Maintenance

The Eastman Nevercold Recirculation Pump Kit is designed for low maintenance. Regular checks can help ensure optimal performance and longevity:

• Leak Inspection: Periodically inspect all connections for any signs of leaks. Address any leaks promptly to prevent water damage and maintain system efficiency.
• Timer Check: Verify that the timer settings are still appropriate for your hot water usage patterns. Adjust as needed.
• System Cleanliness: Keep the area around the pump and valve clean and free from debris.
• Power Interruption: If the water supply is turned off for any reason, it is recommended to unplug the pump unit to prevent it from running dry, which could cause damage.

Troubleshooting

If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact Eastman customer support for further assistance.

Specifications

Warranty Information

The Eastman Nevercold Hot Water Recirculation Pump Kit comes with a 3-year limited warranty on the pump. For specific terms and conditions, please refer to the warranty documentation included with your product or contact Eastman customer support.

Optional Protection Plans:

Additional protection plans may be available for purchase to extend coverage beyond the manufacturer's warranty. These plans are typically offered by third-party providers.

• 3-Year Protection Plan: Available for extended coverage.
• 4-Year Protection Plan: Available for extended coverage.
• Complete Protect: A monthly plan that may cover eligible past and future purchases.

Note: These protection plans are separate from the manufacturer's warranty and are subject to their own terms and conditions.

Customer Support

For technical assistance, warranty claims, or general inquiries regarding your Eastman Nevercold Hot Water Recirculation Pump Kit, please contact Eastman customer support. It is recommended to have your product model number (70600) and purchase date available when contacting support.

You can find contact information on the official Eastman website or within the product packaging.